topblog Ivoire blogs

27/05/2019

Which tool good for 9S12, 908 etc motorola MCU?

Which are good programmers for 9S12, 908 etc motorola MCU?

preferably a one that doesn't require to lift MCU legs and can connect to mcu by connect points on PCB ?

 

There are lots of Eeprom programmer can read Motorola

her are few:

UPA USB

VVDI Prog

Xprog

SMOK

CPT

and many more.

 

Car list + Reviews:

  1. UPA USB read & write 9S12, 908 etc Motorola MCU.

1) Car list:

Motorola HC08*: MC68HC08AS20, MC68HC08AS32, MC68HC08AS60, MC68HC08AZ32, MC68HC(9)08AZ32A, MC68HC908AZ60, MC68HC908AZ60A

 

MC9S12HY64/HA32

 

Motorola HCS12*: MC9S12D64, MC9S12A128, MC9S12DG128, MC9S12DG256, MC9S12H128, MC9S12H256, MC9S12HZ64, MC9S12HZ128, MC9S12HZ256

 

Freescale (Motorola) HCS12X*: MC9S12XD64, MC9S12XD128, MC9S12XDG128, MC9S12XDP384, MC9S12XDP512, MC9S12XHZ256, MC9S12XHZ512

 

2) Reviews:

  1. MC9S12DG128 - 3L40K reading with Xprog

https://www.digital-kaos.co.uk/forums/showthread.php/5429...

 

  1. How to read 68HC05b16 with UPA.

read-68hc05b16-with-upa-01 read-68hc05b16-with-upa-02 read-68hc05b16-with-upa-03 read-68hc05b16-with-upa-04

 

  1. VVDI Prog reads & writes 9S12, 908 etc. Motorola MCU:

1). Support list:

reading MC9S12 series Chips, VVDI Pro is more stable than XP Prog.

attacking MC9S12 series Chips, VVDIProg is faster.

 

MCU

Manufactures

Types

Support

Remark

MOTOROLA

MC9S12XEP

R

Can automatically determine D-FLASH/EEE space

MC9S12XA

R

 

MC9S12XB

R

 

MC9S12XD

R

 

MC9S12XDT

R

 

MC9S12XDP

R

 

MC9S12XDQ

R

 

MC9S12DG

R

 

MC9S12DT

R

 

MC9S12P

R

 

MC9S12H

R

 

MC9S12HY

 

MC9S12HA

 

MC9S12HZ

 

MC9S12XHZ

 

MC9S12B

 

MC9S12GC

 

MC9S12XS

 

MC9S12K

 

MC9S12Q

 

MC9S12C

 

MC9S12P

 

MC9HC(9)08

 

ATMEL

ATTINY

 

ATMEGEA

 

NEC

uPD70F

 

ST

TMS370

 

Note: R means the type is supported, £ means the type will be supported soon in the future.

 

2) Review...

Question: Read car BMW 3 with Xhorse VVDI eeprom came up once read in Tango CAS 3 + encrypted can this be done if I have Isn of car let me know please asp

 

Anser: VVDI prog yes with wires…Eeprom

 

  1. SMOK reads & writes 9S12,908 Motorola MCU:

google and search http://smok.com.pl for official info.

 

  1. XProg reads & writes 9S12, 908 etc. Motorola MCU:

1) XPROG-M V5.84 Authorizations:

AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)

AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0024-1 MC9S12Cxx

AUTH-0024-2 MC9S12XE

AUTH-0024-3 9S12XE SECURITY

AUTH-0024-4 MC9S12HA/HY/P

AUTH-0027-1 HC(S)908 update Authorized 2016/3/13

AUTH-0027-2 HC(S)908 sercurity Authorized 2016/3/13

xprog-908jpg-05

 

2)Reviews on Xprog V5.8 Reads MCU 9S12 XEQ 384 on Rang Rover 2015-2016

Read MCU 9S12 XEQ 384 on Rang Rover 2015-2016

Save P-FLASH and D-FLASH unlock KVM secured

 

Now, I'll show you the location of a KVM module

And dismantle the module with secured MCU 9S12 XEQ

Read on bench using Xprog HQ clone or original

Then save P-FLASH and D-FLASH unlock KVM secured

 

Here we go.

 

Module location inside Rang Rover 2015-2016

xprog-land-rover-kvm-unlock-2

 

Xprog box HQ clone.

xprog-land-rover-kvm-unlock-3

 

The KVM board

xprog-land-rover-kvm-unlock-4

Secured MCU 9S12 XEQ

xprog-land-rover-kvm-unlock-5 xprog-land-rover-kvm-unlock-6 xprog-land-rover-kvm-unlock-7 xprog-land-rover-kvm-unlock-8

 

Pin 42 and 46

Lift 1 pins shown in the image.

xprog-land-rover-kvm-unlock-9 xprog-land-rover-kvm-unlock-10 xprog-land-rover-kvm-unlock-11 xprog-land-rover-kvm-unlock-12

 

Maximum wires length 12cm

xprog-land-rover-kvm-unlock-13

 

Secured MCU 9S12 XEQ 384

xprog-land-rover-kvm-unlock-14

 

Run Xprog software v5.8

xprog-land-rover-kvm-unlock-15

 

MCU/MPU, Freescale NXP 9S12XE, MC9S12XEQ384 D-FLASH-Secured

xprog-land-rover-kvm-unlock-16

Tip & Guide: How to get Xprog to work with secured MCU:

Reset MCU security

Run->change security state->reset MCU security

Wait 10...15 seconds if not success, cancel process

Check connection

Start from a

Remember MCU security byte value

Read, write...commands can be executed many times

Set MCU security

Run->change security sate->set MCU security

Read

xprog-land-rover-kvm-unlock-17 xprog-land-rover-kvm-unlock-18

 

Reset MCU security

xprog-land-rover-kvm-unlock-19

 

It will take 10 to 12 seconds to unlock MCU

IP NOT STOP and repeat

xprog-land-rover-kvm-unlock-20 xprog-land-rover-kvm-unlock-21

 

Read

xprog-land-rover-kvm-unlock-22 xprog-land-rover-kvm-unlock-23 xprog-land-rover-kvm-unlock-24 xprog-land-rover-kvm-unlock-25 xprog-land-rover-kvm-unlock-26

 

Save data

xprog-land-rover-kvm-unlock-27

 

MCU/MPU, Freescale NXP 9S12XE, MC9S12XEQ384 P-FLASH-Secured

xprog-land-rover-kvm-unlock-28

 

Read

xprog-land-rover-kvm-unlock-29 xprog-land-rover-kvm-unlock-30 xprog-land-rover-kvm-unlock-31 xprog-land-rover-kvm-unlock-32

Save data

xprog-land-rover-kvm-unlock-33

 

Job is done.

 

 

That's all.

Thanks.

 

www.obdexpress.co.uk

 

http://blog.obdexpress.co.uk/2019/05/27/good-programmers-...

08:06 Publié dans Car ECU programmer | Tags : xhorse | Lien permanent | Commentaires (0)

17/09/2018

How to use Condor Mini + Tibbe Jaw M3 cut Jaguar 8 cut key

How-to's:How to use Condor Mini + Tibbe Jaw M3 cut Jaguar 8 cut key 

 

It’s aimed to cut a Jaguar 8 cut key with a Condor Mini machine

 

Have just cut the key and it seems to be 1 cut in front / 1 cut behind in placement.

 

 

 

 

 

 

Q: How far should this screw be in / how far out should it be??

 

A: tbe1

 

 

 

 

 

Q: How much does the rear screw need to stick out?

 

A: It is necessary to re-adjust the position of the key in the vice.

 

 

 

Q: what the best way to make sure it lines up in the correct place perfectly.

 

A: With the correct attitude, the machine itself will go to the right distance to puncture the key into the position of the first secret. at Ford it is shorter.

 

 

 

Q: I will give it another go fingers crossed lol

 

A: if properly configured for the Ford device, then do not re-adjust the vise of the length of the bolt. stand the workpiece of the key and cut it

 

 

 

 

 

Q: how far out do you have your screw?

 

A: in the vice, the key is the Ford, and the milling cutter has entered the required length independently. Do not be afraid

 

 

 

Q: the last cut i did was wrong it was to far forward by nearly a complete cut

 

 

 

A: It is necessary to adjust when the milling cutter stands in such position as at me on a photo. remove the vice and adjust the depth of the key with the screw, each time looking closely at how the milling cutter is positioned. The cutter must be in the position of the first secret

 

you do not have a vise

 

as you adjust the screw, tighten the fixing nut so that the screw does not hang and unwind. I'm sorry, I've got to go to the client.

 

try to insert the key deeper. with effort.

 

Source:http://blog.obdexpress.co.uk/2018/09/17/condor-mini-tibbe...

 

04:36 Publié dans car key programmer | Tags : xhorse | Lien permanent | Commentaires (0)