topblog Ivoire blogs


Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Topic :how to use Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Here you are:


copy the immo information from a cluster to another

make the mileage follow with the immo information



Audi a4 2001


Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA-USB programmer


Original cluster:

The Jaeger cluster barely works

audi-a4-2001-cluster audi-a4-2001-cluster-1 audi-a4-2001-cluster-2


read the pin code from both the Instrument and adapt it to the vehicle


What to do on pin 21 and 22 on the chip:


- With ECU programmers:

Eprom.set type,mcu,hc12,read,save.

eprom,set type,mcu,hc12,file,load,write.

Buy yourself Xprog-M programmer, Carprog, UPA-USB.

Pin 21 and 22 jumper after programming or wait 10 minutes.


- with Digiprog3:


Eprom,set type,mcu,hc12,read,save.

eprom,set type,mcu,hc12,file,load,write.



Eeprom HC12 read and write to the other counter:



(Write down the exact ALWAYS old / incorrect Mileage)

The diagnostic port is in the driver's footwell. Turn the ignition

on a vehicle. Connect plug ST16 the diagnostic port and the



Select the program: cars / trucks - AUDI - MM 4 / 99- DIAG.

The DIGI PROG II shows you the old / incorrect Mileage.

Enter the new / correct Mileage and confirm this.

Should be then after programming on the speedometer 999999 KM give

The old / wrong KM value again so that the speedometer again the old /

false indicates KM. Now you build the speedometer and break it to the

see board. Solder the green and black wire to the same color marked

Arrows at. Now connect the blue and the green plug with

the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)

Now select the program: cars / trucks - AUDI - MM 4/99 HC12.

The DIGI PROG shows you the old / incorrect Mileage. Enter the

new / correct Mileage and confirm this with the hook.

Now shows you the DigiProg II 5 min wait. Remove the connection

between the DigiProg and the speedometer, wait 5 minutes and build the speedometer

again. Alternatively, for 5 min. Wait, you can also like in the image on the

next page shows the pins 21 and 22 bridges.


Here necessarily the board from any power supply (Digiprog,

external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer

Immediately reinstall.


OBDexpress disclaimer:


Thanks for all tech support from members’ share at


How to use Digiprog 3 for Ford Mondeoodometer correction

Confirmed! Digiprog 3 can correct the mileage on a Ford Mondeo through OBD.

Connect the DP3 unit to the car thru the OBD port


Power on

digiprog-3-ford-mondeo-odometer-correction-3 digiprog-3-ford-mondeo-odometer-correction-4

Enter password


In the DP3 main menu, select CAR/TRUCK



digiprog-3-ford-mondeo-odometer-correction-7 digiprog-3-ford-mondeo-odometer-correction-8 digiprog-3-ford-mondeo-odometer-correction-9 digiprog-3-ford-mondeo-odometer-correction-10 digiprog-3-ford-mondeo-odometer-correction-11 digiprog-3-ford-mondeo-odometer-correction-12 digiprog-3-ford-mondeo-odometer-correction-13 digiprog-3-ford-mondeo-odometer-correction-14 digiprog-3-ford-mondeo-odometer-correction-15 digiprog-3-ford-mondeo-odometer-correction-16

Current odometer: 189237km

digiprog-3-ford-mondeo-odometer-correction-17 digiprog-3-ford-mondeo-odometer-correction-18

Go for odometer correction

digiprog-3-ford-mondeo-odometer-correction-19 digiprog-3-ford-mondeo-odometer-correction-20


Enter new KM: 183000

digiprog-3-ford-mondeo-odometer-correction-22 digiprog-3-ford-mondeo-odometer-correction-23 digiprog-3-ford-mondeo-odometer-correction-25 digiprog-3-ford-mondeo-odometer-correction-25

New KM displayed on the dashboard

Digiprog 3 changed KM successfully.

Job’s done!

Other options for Ford odometer correction:

Obdstar F100:

Designed for Ford/Mazda odometer correction and key programming

Obdstar H100:

Esp. for Ford/Mazda 2017-2018 models dometer correction and key programming

Obdstar X300M:



Why Digiprog 3 wins?

Lots of new odometer correction tool flooded into the market. But you’ll find that topics of Digiprog 3 china clone never end in the automotive forums. People keep interest in and give good reviews of this tool. Most Digiprog 3 purchased is very satisfying!


Digiprog 3 odometer corrction tool


Look here.. users share their OK and K.O. experience. And here, Laura collected all for you. Hope it helps.




Audi a1 works (depending on software number)

Audi a2-obd -ok

Audi a3-repair 999999 in dash with digiprog

Audi A3 2010 by OBD OK

Audi A3 2002 obd2 is ok

Audi a3-2001-vdo-obd ok

Audi a4 2001-2005-obd ok

Audi a4 8e b6 2004 obd ok, use 2 minutes

Audi a4 2007 obd dash read ok write ok/ecu make-it via touran edc16 write 2 times to change.

Audi a4 2009 3.0quattro obd ok

Audi a4 2005-2009-obd ok

Audi A4 2010 Work

Audi a4 2012 obd ok and fast

Audi a5 2013 obd ok

Audi a5-2010-obd ok 15 min

Audi a6 c5 obd

Audi A6 2002 ok after some effort.

Audi a5 2009 3.2L obd ok 30min

Audi A6, 2009 work OBD, 4-5 minute.

Audi A6 2010 dash via obd (takes a while to find code but ok)

Audi A8 4.2 tdi 2008 Dash OBD OK 2min

Audi S3 2002 obd2 is ok

Audi TT 2002 obd2 n8 is ok

Audi q3-2010-obd ok 15 min

Audi Q5 2.0tdi 2010 by obd …20-30min

Audi Q7 2012 20 sec by obd work ok

Audi Q7 2007 —>OBD work

Audi q7-2008-obd ok

Audi tt hc 12 plug ok


BMW I82017 work..unit from ebay

BMW E46 2004 —> 35080 Clip Work

2001 bmw x5(e53) sure ok and also range rover with same dash. no problem.

have to take dash out and solder on back of board.

can use BMW 35080 option.


Corolla verso 2007 ok with luck


Chevrolet Montana obd ok

Chevrolet Cruze 2011 obd ok

Chevrolet Aveo 2012 obd ok

Chevrolet Corsa obd ok (after unplugging battery for a few secs)

Chevy suburban 2007 ok if you disassemble dash and read 95080 using eeprom menu then calculate manually. Will not do it by OBD. Be sure to include Km or Mi, original mileage, desired mileage and hours.


Citroen DS3 93C66 new release DS4 24C16

Citroen C3 / DS3 new releases

Citroen Jumper 2007

Citroen: DS3 C3 C66 Case3: hc12x new release

Citroen C3 programming via Tacho & Box

Programming Citroen C5 via Box & Cluster

Citroen C5 Programming 2003 via chips

Citroen C8 programming via Tacho & BSI

Citroen Saxo New diagnosis

Citroen Picasso NEC Tacho & Box via Micro & Chip

Citroen Relay Van Chip 95040 Chip Programming

Citroen Xsara 2000/2002 NEC programming via BSI & Tacho chips

Citroen Belingo 2003/2004 Cluster and BSI Programming

Programming Citroen Belingo HC08 Tacho via Micro

Citroen C3 programming via the chip

Citroen C5 New software programming via cluster & BCM

Programming Evasion Citroen via puce

Citroen Relay programming via chip

Citroen Xantia programming via chip

Citroen Xsara programming via chip

Programming Citroen Xsara via BCU & Tacho


Ford transit 93c76 eeprom ok

Ford fusion hc 12 plug ok

Ford mondeo 2008-ond ok

Ford focus hc11-ok with plug

Ford focus 2006 obd ok

Ford focus 2004-2010 obd ok

Ford s-max 2009 obd ok

Ford Fiesta 2012OBD OK (fiesta 2005 obd not ok)

Ford fiesta 2008-2010 red screen obd ok

Ford Fiesta HCS12 —> ST48 Work

Ford Mondeo 2008 Full Colour Fis 24C16 – – – OBD diag Read – 0km ,Write – OK!

Ford mondeo 2010 visteon dash with 9s12 read ok write ok via 4 wires on pcb

ford mondeo 2004 st51 read ok/write ok

Ford Bantam 2006 need nec programmer

Ford connect 2008 obd not! fvdi obd, read km but not change! dp3 ,conector 48, 9S12read and write km!


Fiat ducato 2014 obd dash ok (ecu 95640) but nyo 2015 suport


Galaxy 2008 new model by the OBD ok


Honda crv 2002 dash (68hc912)

Honda civic ep3 type r 2002 eeprom OK


Hyundai I10 (No connection i10 mcs12hy64 to digiprog ….if its 24c08 use plug 1)

Hyundai Terracan w nec, adapter st59, 100% ok, working


insignia 2011 obd ok 1min

Land Rover Discovery 4 24c16 tacho – ok

Range Rover sport 2010 24c16 tacho – ok

Range Rover evoque 2013 via obd ok


Mazda b2500 – b2900 ok


Mercedes w204 c250 2011 obd ok (Just put through as ezs, it will block sync and do dash)

Mercedes w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok

Mercedes w210 obd

Mercedes w211 and do obd

Mercedes w219 works as w211 just flashes dash obd

Mercedes W251 R350 2010 ok OBD (no sync problems no can filter needed)

Mercedes class B W246 use direct in OBD

Mercedes vito 638 2003 OBD ok

Mercedes W211. Cluster is no problem via OBD. For EZS, need a cable called HC12.

Mitsubishi galant 2006 93C46 ok

ercedes Vito W638 2003 OBD ok

Mercedes class B W246 direct use in OBD ok

2003 Read and Save Group the Mercedes EEPROM via EEPROM / MCU ok


Nissan navara , pathfinder motorola ST48 by points OK

2011 Nissan micra 1.5 tekna 93c66 eeprom use honda accord c66 option on digiprog same algo by desoldering and using clip st01 to read and write no need to remove needles chip on back of board


Opel Vivaro 2013 —> EEPROM Clip work 93c76

Opel Astra H —> 35080 Clip Work

Opel astra h 2006 – m35080 – work

Opel Astra 2000 obd ok

Opel insignia 2013 obd –OK

Opel Insignia 2014 —> OBD Work perfect

Opel Corsa, the digiprog working.

Opel Corsa c and astra g. Read and out new mileage in. When press tick, hold trip button and ofometer will flash. When digi says check value, release button and disconnect battery for 10sec–> Job done


Peugeot 307 2002 —> Work, Dash —> NEC (New ST59), BSI —> HC12

Porsche panamera 2014 by eeprom 95640 work ok


Saab 9-3 2009 HCS12 ok

Seat MII 2013 —> OBD Work


Skoda Superb (3t) II 2009y only by obd less then 5min

Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok

Skoda Octavia 2010Y 1.6TDI cluster via obd

Skoda Octavia 1z 2011 OBD ok

Skoda Fabia MK2 2009 diag no problem

SKODA Fabia 2009 obd ok.

Skoda Roomster 2009 —> Diag work Perfect


Toyota yaris(2011), remove and clean chip to read/write, need luck

have to look first which eeprom on circuit my experience with some toyota that they use a small 93C46 wich is not in the menu


Volvo xc90 2007 dash ok by soldering

Volvo xc60 2009 obd ok

Vauxhalls Vivaro2011… 93c76…. All good… read and write..

93c76 option not available under Renault Traffic so use Vivaro or maybe try Renault Master as has 93c76 option that seems as though it would work, have not tried, read ok but didn’t i write chip…

Volkswagen Eos obd2 ——ok

vw eos 2007 —> Diag obd2 work

vw polo, seat ibiza 2007 magenti marelli motorola ST48 by points OK

vw polo 2001-2005 vdo obd ok

vw polo trw plug ok

Vw fox 2007 hc912 by solder point and ST48 work

Vw touareg 2004 obd ok

Vw Tourag 2013… read ok but write failed

VW Tiguan 2007 —> OBD OK

vw tiguan 2010-2011 OBD ok

Vw AMAROK 2012 obd ok 1 min

vw bora all obd ok

vw jetta all obd ok

vw jetta 2012 work obd

vw t5 obd ok

vw t5 ecu edc 16 ok 50%50

vw touram dash obd ok

Vw Golf 4 BOO via OBD ok and Audi a4 boo crypto too

Vw Golf 4 without problem!!!

Vw Golf 5plus by obd -visteon dash read ok write ok

Vw Golf 6 plus 2010 work ok

vw Golf MK6 2012 works OK

Vw Golf 6 work good till 2013 year

Vw Golf 6 plus 2010 Works ok

Vw Passat 2013 obd..ok

Vw passat 2007 obd ok

Vw passat 2008 via obd-dash read ok write ok/ecu read ok write ok 5 min.

Vw Passat CC 2.0tdi 2010y done by obd

Vw passat 2006 tdi dash & ecu obd OK

Vw passat 2001-2011 obd ok

Vw passat 2011 work obd 5 min

Vw passat 2012 work obd

Vw passat cc 2012 work obd

Vw Passat b5 2003 tdi all ok

VW Caddy 2013 jet menu makes Golf 6 2012>

VW Touareg 2004 OBD ok

VW Polo, Seat Ibiza 2007 Magneti Marelli Motorola ST48 by OK points

Seat Leon 1M 2000 2002 and 2003 via OBDII no problem

T5 2004 dash & ECU via OBD -read? / Writing ok 10 seconds. ECU EDC16 read write ok 7 minutes

Sharan 2001 via OBD-lu? / Writing ok

Skoda Octavia 1z 2011 OBD ok

Skoda Fabia 2009 OBD read? / Writing OK

Skoda Fabia 2010 OBD, read? / Write OK after second try


reads 9s12 mcu with cables 48 and 51


Complicated with the EPROM of Peugeot 508 2012…

Need open dashboard, and Bsi.

Peugeot 508 have eproms. 95080 and 95256.

Read them, then put them here

Peugeot 508/508 new version

Peugeot 106 diagnostic

Peugeot 206 Programming Jaeger via Micro

Peugeot 206 M2002 NEC All new programming modules via chip

Peugeot 306 VDO Diagnostic Cluster

Peugeot 307 chip programming via Box & Tacho

Peugeot 307 HC12 Microphone Programming

Peugeot 406 Programming Jaeger via Micro

Programming Peugeot 406 Sagem via chip

Peugeot 406 Valeo Box Programming by Box & Cluster

Peugeot 406 VDO Diagnostic Cluster

Peugeot 406 VDO 2000/2001 Cluster + BCU

Peugeot 407 Programming by Tacho & BSI

Peugeot 607 Programming VDO via Cluster Box +

Peugeot 806 Jaeger / Programming Magneti Mareli via Micro

Peugeot 807 Programming by Tacho & BSI

Programming Peugeot Boxer via chip

Programming Peugeot Partner via chip




Cars that Digiprog 3 FAILED to do:


Audi A3 2014 dash 8V , obd not connect


BMW X1 2013 failed… no bmw after 2002 can go by obd… have to program the 35160 chip in cluster and the cas4 (or fem?) module.

or cluster + can filter cable behind cluster to block cas. but digiprog can’t program 35160


BMW 325 e90 or x5 e53 no luck with digiprog via obd2. Cas3 just says no connection or just give me a 1349652 miles which is wrong.


GMC yukon 2001 cannot do via obd


Hyundai I10 9S12HY64 cannot work… Digipro can’t read D flash memory , so it cannot read and write this kind of mcu like Hyundai eon,Hyundai i 10 so use UPA USB can do it.


Chevrolet Cruze 2012 obd didn’t work. remove BCM next to left foot passenger seat you’ll find 24c16 ok


Mercedes W245 digiprog can’t doby obd.

use cluster plug or program chip.

first set to 999999km. then install cluster and put the car on contact for 1minute. then program cluster to any value.

It’s the same for w169


Mercedes Sprinter 906 need to program ezs (cannot with digi , but XprogR270 programmer working no issues)

or use can filter. (yes they exist)


Nissan pathfinder 2000 c56 eeprom, cannot read. Had to do it with TU. Very disappoint couldnt do no 9s12 with digiprog.


Opel astra g, corsa c, zafira a, never have success to do with digiprog by obd


Opel insignia 2010 obd not work.


VW polo 2012 johnson control nec 95320 kill checksum dashboard error … (x-tool or another good tool can fix it)


VW Golf 6 2013 OBD NOT OK


Volvo xc60 obd 2013 won’t go. Only does till 2010


Note: for models with no luck, perhaps obdstar x300m is a good choice. Anyone can try it. i don’t have this. But the reference may help you if you fail with DP3

The best user buying guide of digiprog iii incl Digiprog 3 for sale(best price), update, manual, review, FAQ, car list… at here :