topblog Ivoire blogs

28/11/2017

Free Download Ksuite 2.08 & Reset Ktag + Kess V2

Here is how to reset Ktag and Kess v2 ecu programmer.

1.Download version ksuite 2.08 here

2.Buy new sd card 1gb-2gb and format in fat32 ussing this program

3.For kess use this cfg and 4 file

Copy on sd card 4 file and in ksuite 2.08 open folder update and copy update folder

Connect kess and wait for update all protocol

4. For ktag buy new sd card formaat in fat32 with program posted and copy 3 file on sd card and update on folder update in ksuite 2.08 connect ktag and wait for update all protocol.

Ksuite 2.08 setup

ksuite-2.08-setup-download

 

HDD format

hdd-forma+

 

Kess 4.036-K09021102-full.rar

reset-kess-v2

 

Ktag

reset-ktag

 

 

Use only ksuite 2.08

Enjoy.

 

Free Download Ksuite 2.08 & Reset Ktag + Kess V2

Here is how to reset Ktag and Kess v2 ecu programmer.

1.Download version ksuite 2.08 here

2.Buy new sd card 1gb-2gb and format in fat32 ussing this program

3.For kess use this cfg and 4 file

Copy on sd card 4 file and in ksuite 2.08 open folder update and copy update folder

Connect kess and wait for update all protocol

4. For ktag buy new sd card formaat in fat32 with program posted and copy 3 file on sd card and update on folder update in ksuite 2.08 connect ktag and wait for update all protocol.

Ksuite 2.08 setup

ksuite-2.08-setup-download

 

HDD format

hdd-forma+

 

Kess 4.036-K09021102-full.rar

reset-kess-v2

 

Ktag

reset-ktag

 

 

Use only ksuite 2.08

Enjoy.

 

18/08/2016

How to reflash CARPROG Full V8.21MCU AT91SAM7S256

Here is a experience from DK forum members who made this possible about how to reflash CARPROG Mcu AT91SAM7S256
Tool use: Carprog clone v8.21 firmware 
We need the stuff:
1- AT91SAM7S256.bin
2- Jtag programmer
3- Jtag software

We need to prepare the Carprog to connect to Jtag programmer but first the flash need to be erased, the Jtag function in mcu is disabled, you can't connect to the mcu before erase the flash. Remove the AT88SC eeprom from the board, please note where is the pin 1 in eeprom before remove:
reflash-CARPROG-Mcu-AT91SAM7S256-(1)

Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it with a small ammount of silicone (you don't want to broke the pin in the process).
Connect the Carprog (with the pin 55 dissconected) to the 12v supply, wait about 10 seconds and connect the wire from pin 55 to Vcc (3.3V) in Carprog:

 

carprog

 

reflash-CARPROG-Mcu-AT91SAM7S256-(2)reflash-CARPROG-Mcu-AT91SAM7S256-(3)
Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect the 12v supply from CarProg full  and remove the pin 55 wire from vcc. The pin 55 must remain disconnected until the programming process is done.

 

Ok, that’s it. I make it; and you try on you risk.

Original:http://www.obdexpress.co.uk/service/reflash-carprog-full-...