topblog Ivoire blogs

30/06/2016

How to use K+DCAN cable for BMW airbag ECU replacement

You will learn how to replace BMW airbag ECU using K+DCAN INPA USB cable + NCS Expert software.

You need:
7mm socket
10mm socket
1/4" extensions
1/4" ratchet
screw driver
NCS Expert
USB OBD cable for BMW
OBD2 20pin cable
You can get the adapters on obd2express for €15-25. For you'll need the usb OBD2 and the OBD2 20 pin adapter, so you are advised to buy a bundle to save money (K+DCAN cable + 20pin to 16pin connector). The software also can be got in the package for free. You should head to the diagnostic sub-forum, because there's ton of information about diagnostic tools. NCS Expert is part of EDIBAS. So, the cables you need should be like these:

new-bmw-inpa-kcan-cable-with-ft232rq-chip.jpg

bmw-20pin-to-16pin-diagnostic-connector.jpg
Step-by-step instruction on BMW airbag ECU replacement:

NOTE:
Follow the instruction below AT YOUR OWN RISK.
1. Remove the battery negative cable.

2. To remove the rear cup holder lift up the rear vent (1) and pull the cup holder (2) out.

bmw-airbag-ecu-replacement-NCS-expert (1).jpg
3. Pull down the rear vent (1) and remove.

4. Remove the two screws and two nuts circled in red.

bmw-airbag-ecu-replacement-NCS-expert (2).jpg
5. Remove the armrest and the tray under it.

6. Remove the two easily accessible nuts holding the airbag control module.

bmw-airbag-ecu-replacement-NCS-expert (3).jpg
7. The third is a bit tricky to get to. It can be access via the hole circled in red. In the first picture you can barely make out the nut. In the second I've pushed the rear air duct to gain access to the nut. Any of my sockets didn't fit through the hole so I had to put the extension through it and then install the socket on it inside the center console. A bit tricky to do, but not too bad.

bmw-airbag-ecu-replacement-NCS-expert (4).jpg
8. Remove the Airbag ECU connector. This type of connector is used in number of places on your e39. You'll need to pull the green locking clip towards the rear of the car to release it. If you want to practice how to do it you can find similiar connector on Cd-changer, NAV computer etc.

9. Take out the old Airbad ECU and install the new one. Remember to put back the grounding wire under the nut (1).

10. Assemble everything back together. To install the third nut put a piece of paper between the socket and the nut so the nut won't fall off.

11. Code the new Airbag ECU. I did this with NCS Expert. A great how to code with NCS expert can be found at http://obd2-diag.blogspot.com/2016/06/bmw-coding-with-ncs...

05:06 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

29/06/2016

Multi-Diag Access J2534 prompt "the update of the communication interface"error

From OBDexpress customer response, after the Multi-Diag Access J2534 software installed, when work with his car get a prompt "the update of the communication interface" below, in this page, to not bottom go to, the LED lights flashed not bright..

multi-diag access j2534.jpg
Solution:
1. To reconnect or for the other car
2. If the LED is not bright, that equipment is broken, need to send back to repair

Attention:
1. Pls disconnect the network when install the software.
2. Pls follow the installation video to install the software and drivers.

04:12 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

28/06/2016

TM100 Transponder Key Programmer full version update to V3.36

New Release V3.36 TM100 Transponder Key Programmer full version with 62 Modules in OBDexpress only for €1,681
 
TM 100 -------2016-6-24 V3.36 released
1. Add keymaker for Suzuki Swift, Maruti Swift. Parts: Immobox, IC: 93C86, Transponder: HITAG2
2. Add new type 24C16 support for Mitsubishi ASX, Outlander
3. Add keyexplorer for Renault Koleos, Megane
4. Bugs fix for ID46 image generator
5. Bugs fix for keymaker Chrysler 300C 9S12, 93C86
6. Bugs fix for keymaker Volvo V40 9S12
7. Bugs fix for keymaker Renault Laguna 95160
8. Bugs fix for keymaker Hyundai Accent 95040
9. Bugs fix for keymaker Renault Espace III HC08
10. Bugs fix for keymaker Hyundai Santa Fe 95P80
11. Bugs fix for write 7-byte CS for VAG
12. Bugs fix for locking Tiris 4E
 
Free download:
TM100 Transponder Key Programmer free and charging model list
 
Online authorization method:
1. Make sure the computer networking
2. "Install New Module" main menu, select "Tools" and select from autocomplete license updates

tm100-transponder-key-programmer-authorization-1.jpg
TM100 for BMW special functions:
1.BMW EWS1, EWS2, EWS3, EWS4
2.BMW CAS1, CAS2, CAS3, CAS3+, CAS4, CAS4+
3.BMW motorcycle HITAG key
 
TM100 for Toyota/Lexus special functions:
1.Toyota H reading
2.Cover all Toyota and Lexus models(Tiris 4C, Tiris 4D, Tiris DST+, G chip and Smart key) except for latest type H transponde
3.Toyota/Lexus Smart key car list: Land Cruiser 200, Land Cruiser Prado, RAV4, Venza, Corolla, Lexus:LX 570, GX 460, RX, LS 460, GS, IS
 
How to use TM100 transpoder key programmer to make new TOYOTA G when you lost all original key
1) Remove IMMO box from instrument cluster
2) user XPROG M to read out the 93C66 data and save it to your PC.
3) Open TM100 software, find 93C66 module of Toyota Camry after 2005
4) Clike "open file" to upload 93C66 data you saved before.
5) choose "use original facotry chip", click "OK", Choose "Key position 1" to write start. Then TM100 will generate the new data.
6) Write this data back to 93C66.
7) Install the IMMO BOX back to your car. Use the new key to start your car directly.

04:46 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)