topblog Ivoire blogs

20/07/2016

How to use KTAG KTM100 to read BMW F10 EDC17C41 [tips]

Here are some tips of “reading error” for you when reading EDC17C41 DDE8 520d F10 ecu with Ktag clone, offered by experienced users.

TRY OWN YOUR OWN RISKS!!

Tip 1 - replace oscilator near the nxp processor on ktag board

ktag-replace-oscilator-1.jpg
Tip 2 - need boot and 2 rainbow cable yellow and orange and you have placed the yellow and orange on the wrong spot

k-tag-rainbow-cables-2.jpg
1.GREEN-CAN L
2.ORANGE-VKEY
3.YELLOW-K LINE
4.ORANGE-VKEY
5. RED-VECU
6.BLACK-GND
7.BLACK-GND
8.PURPLE-VPP
9.RED-VECU
10.WHITE-CAN H

Tip 3- to rework ktag hardware is necessary with good component, buy too necessary good power supply

ktag-rework-3.jpg
Tip 4 - ECU tuning tools for reading BMW F-series EDC17C41
Ktag v6.070 --> YES
Need rework hardware to read EDC17C41 as tips above say
KTM100 v7.003--> YES
BMW ecu EDC17C41 is newly added in KTM100 fw: v7.003

ktag-ktm100-kess-v2-EDC17C41-ok-4.jpg
FGTech--> Risky to try!
ECU EDC17 C41 - TC1797 Internal Flash

FGtech-EDC17C41-5.jpg

FGtech-EDC17C41-6.jpg
Kess V2--> NO!!
Kess v2 can’t read and write this type of ECU (EDC17C41), ECUs on the same car model in different areas are sometimes encrypted in different ways, and therefore the tool cannot always work on the same car model.

kess-v2-EDC17C41-failed-7.jpg

kess-v2-EDC17C41-failed-8.jpg

kess-v2-EDC17C41-failed-9.jpg

kess-v2-EDC17C41-failed-10.jpg
NOTE:
WE’RE NOT RESPONSIBLE FOR ALL YOU WILL TRY.
GOOD LUCK.

08:05 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

19/07/2016

FGtech Galletto 4 vs CMD flasher vs Alientech Ktag Kess v2 vs MagPro

I was playing around with my MB Star C4 and Xentry 2016 developer mode

and I might have found a alternative to delete the ABC warning lights without a module.

Tested on 2003 Mercedes-Benz CL600 Base Coupe 215.376 5.5L V12

FOR THOSE WHO WANT TO CONVERT TO COIL-OVER and remove ABC suspension forever

So, here is what I found, someone can test it but you have to have DAS Xentry with developer mode.

I can’t test it as I already have the module installed and no time right now

If nobody can test it, I will do it one of these days

follow this:

Go to Control unit

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (1

 

->body

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (2

 

 

->CGW(cental gateway)

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (3

 

 

->development data

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (4

 

->control unit adaptations

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (5


->control unit adaptations (variant coding)

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (6

->globale variantencodierung

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (2


->nicht vorhanden

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (8

 

(giving a 1000 thx to pmercury in the mbworld)

 

Invested on Chinese ECU programmers, FGtech Galletto 4, CMD flasher v1251, clone Alientech (Ktag and Kess v2), MagPro x17... I read a lot, with each opinion. Over all that I read is old (<2011).
So here's what I remember:

fgtech-galletto-4-master-bdm-tricore-obd-function-final.jpg
- FGTech Galletto 4: it is the best product, many times cheaper than the competition, at 40 euro you have a good Chinese clone for all cars, trucks, motorcycles, Marine, BDM MPCxx, BDM Boot Mode, checksum etc ... Good support

free-shipping-cmd-can-flasher-v1251.jpg
- CMD flasher v1251: The Must, one diagnostic interface, for reading and writing flash memory on the CAN line (not K-line) of computers with motor MED9.1, MED9.5, EDC16U3x/CP, EDC16CP31, EDC16CP36, EDC16C3 and EDC16C9 fuel injection. you need this tool only for new vag ecus, cause they are obd, even tprot

Magpro2-x17.jpg
- Magpro2-x17: This is very good for the latest ecu cars only and for Denso also you have good support .
All X17 owner will get new hardware soon, all in one tool, BDM, OBD, boot + +

ktag-ecu-k-tag-programming-tool-master-unlimited-token.jpg
- Alientech: Great tool, support is correct , but as soon as you want to touch anything other than car, it's very expensive too (full 20 000 euros) + XXXX euro subscription.

Chinese KTAG and Kess v2 runs the same software as Alientech
Ktag supports protocols: BDM MOTOROLA MPC5xx
Kess v2 supports Line, CAN, EDC17 and MED17 and Ford J1850... and Kess v2 truck version is available
they both work good, same as original and without tokens limitation, perfect with checksum, compared with FGTech

kess-v2-obd2-tuning-kit-vehicle-list.xls
kess-v2-truck-list.pdf
kess-v2-supported-truck-list-comparison.pdf 

05:21 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

18/07/2016

Tango Key Programmer Update to V1.106 adds more free software

Tango Key Programmer Update to V1.106 adds more free software in obdexpress.co.uk,and free software listed below:

Tango V1.106 Update Software List (for Free):
[+] Techtream calculator: v9.30, v10.10
[+] Key maker Citroen Jumper 2012-(95640,HITAG)*
[+] Key maker Isuzu NPR 2007-(93C56,HITAG)
[+] Key maker Peugeot 206 2001- (95160,HITAG)
[+] Key maker Peugeot Partner 2002- (95160,HITAG)
[+] Image generator Chevrolet Spark (ID8E)
[+] Cloning of Toyota and Subaru 80 bit Keys**
[+] Added transponders CN2, CN5 to the Clone mode

How to distinguish the original and copy Tango Key Programmer?
Our Tango is original. For original device, there is the serial number. You can use this serial number to register your information on official website, then download the latest software to update your device online.

Update:This one is original. You need to update it when new software release.

Attention:After generating a new transponder with TANGO Programmer, you will not need any additional diagnostic equipment to program the generated transponder to the car! It will start the car directly, even on new FIAT CODE 2 system, also used in PSA Group vehicles! Only you have to write the new file back into the immobilizer system!

How to update Tango programmer to latest version:
1) Go to help option
2) Click online update

tango-key-programmer-with-basic-softwared-a-des-6.jpg
List of supported transponders:

Philips transponders:
PCF7930-31 writing, reading
PCF7935 writing, reading, shadow memory, crypto calculator
PCF7936 writing, reading, modes password, crypto, Manchester & Biphase encodings
PCF7941 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7942 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7943 transponder, remote, Manchester & Biphase encodings
PCF7944 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7945 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7946 transponder, remote, Manchester & Biphase encodings
PCF7947 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7952 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7961 transponder, remote, Manchester & Biphase encodings
*Auto switching between PCF7936-PCF7961 windows if invalid type detected.
*Autodetect manchester / biphase

Temic transponders:
Temic 11 reading , writing to T5
Temic 12 reading , writing to T5

Megamos transponders:
Megamos (13) reading , writing to T5 , emulating on PCF7930-35
Megamos (48) reading, writing, PIN, unlock by PIN, full range of memory contents, crypto calculation
Megamos CRYPTO-2 (8E) read ID, read/write EEPROM, write Cryptokey

Texas transponders:
Tiris (4C) reading
Tiris (4D) DST crypto reading, writing, crypto calculator
Tiris (4E) DST crypto reading, writing, crypto calculator
Tiris (8C) reading

Atmel:
TK5551M (T5 replacement)
SAAB reading , writing to T5
The product is in working out stages, therefore the list of the supported transponders will be developed later.

http://www.obdexpress.co.uk/wholesale/tango-key-programme...

05:39 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)