topblog Ivoire blogs

16/02/2017

Read / write / save BMW CAS4 Via VVDI PRO Step Guide

Here is a tutorial of using xhorse VVDI PRO programmer to Read / write / save BMW CAS4 with highly secured MCU MC9S12XEP100 Masked as 5M48H inside

Main step guide below:

Open VVDI Prog software, select type, manufacture and model as MC9S12XEP100)

Click "Wiring Diagram"

Maximize wiring diagram: right click and select "zoom window", then pull down window.

Follow the wiring diagram to connect CAS to the VVDI Programmer.

Start to connect the cable.

The left zone is done, next is to do the right zone.

In this wiring diagram, it only need to remove one 0 ohm resistor to read out data, but one CAS ECU structure is different another one, some needs remove more electronic parts; we will show how to do in the other videos.

Next is to remove this 0 ohm resistor.

Wiring is done, 0 ohm resistor is removed

Plug adapter into VVDI Pro.

Close wiring diagram.

Select "New" – " Read"

You see it is reading data very fast.

Reading data successfully, click "Save"

Next is to check data.

Open the data, drag the mouse to check, okay, data is all read out, close it.

 

Attach photos of the reading procedure

How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer


How to read / write / save BMW CAS4 via Vvdi Prog programmer

 

Enjoy!

 

 

15/02/2017

VVDI MB Tool exchange W204 ESL without renew EIS

 Vvdi mb tool 2.1.6 update info about W204 esl:

Exchange W204 ESL without renew EIS. In ESL Tools, write EIS with password(Select Auto clear TP and personalized)

 

Note: vvdi mb tool 2.1.6 download

 

For users with the vvdi mb bga tool:

As for w204 Faulty ESL unlock and renew all works fine + when rematching to EIS there is no need to Get Erase Pass or Renew EIS any more since the latest update (v2.1.6),just get Key Pass and paste it to the EIS dump close go to ESL use Load Vvdi ESL Data + tick Auto Clear TP + Write all set to go.

 

detailed screen shot in the post below

Vvdi mb tool 2.1.6 update info about W204 esl






 

source:http://www.obdexpress.co.uk/service/vvdi-mb-tool-exchange...

14/02/2017

Honda HDS Key Programming with HDS HIM diagnostic tool

To add one new key/Keyless transmitter, you need:
1. Immobilizer Mater Key Blank or Immobilizer Valet Key Blank 
2. One programmed ignition key (master or valet) for the vehicle
3. Vehicle key code
4. PCM code
5. Honda HDS HIM diagnostic tool with immobilizer programming software
 HDS 3.101.015 (!! cheap honda hds cable only for diagnosis)
The HDS is required for registration of the immobilizer keys. Programming the immobilizer also programs the keyless transmitter.
Use the HDS with Honda key blacks to add a key or keyless control unit, storing the transponder code of the new key in the memory of the control unit.
6. Condor XC-MINI key cutting machine

NOTE:
Make sure the market, the date, and the time on the HDS setup screen are correct. 
Select the F12 key in the upper right corner to get the Set-up Details screen.
Make sure Market is set to USA. 
Select the time display in the lower right corner to get the Date/Time Properties pop-up window.
 
How to program a new key to Honda with Honda HDS scanner:
1) Use an appropriate key blank and the key cutting machine to cut a new ignition key.
2) Connect the Honda HIM diagnostic system with vehicle via OBD socket 
3) Insert a programmed ignition key into the ignition switch 
4) Turn ignition ON
5) Run Honda diagnostic system personal computer (pc) software and come to iN screen 
6) At the screen prompts, enter the VIN and the odometer reading, then verify the correct date and time.
7) Select “IMMOBI” from “System Selection” Menu
8) Select “Immobilizer Setup” from “Immobilizer Test Mode” Menu
9) Select Add and Delete Keys 
10) Select Add 1 Key 
11) Select Begin to Add 1 Key 
12) Follow the HDS screen prompts, if your HDS is not logged in to the iN, you willhave to enter the PCM code you have retrieved from the iN Immobilizer Code Inquiry to proceed. 
13) When adding keys procedure completed, turn ignition OFF
14) Exit HDS software and disconnect Honda HIM HDS scan tool from the vehicle
 
 
P.s. This is the Honda HDS pocket tester in use.
Honda-HDS-Key-Programming
Honda-HDS-Key-Programming