topblog Ivoire blogs

24/04/2015

How to use Lexia-3 PP2000 XS Evolution to Program New Keys for Peugeot

Lexia-3 PP2000 XS Evolution with Diagbox V7.57 is an auto diagnostic tool that supports read identification and read fault codes (for normal use) etc. for most of Citroen and Peugeot vehicles from 1995 to 2013, while here I would like to show you how to program Peugeot new keys with Leixa-3. 

 

Attention: PIN Code is required during key programming procedure. Record your vehicle PIN code first.

 

Procedure to program Peugeot new keys:

1.Install and activate Lexia 3 xs Evolution PP2000 V25 diagnostic software.

2.Select vehicle model 307 and wait until the well communication built.

3.Check the entering vehicle information.

program Peugeot new keys-1.jpg

4.Select the application as "Peugeot Plant 2000" and confirm it.

program Peugeot new keys-2.jpg

5.Select test by ECU;

6.Choose "Built-in systems interface";

program Peugeot new keys-3.jpg

7.The system is reading the ECU in progress, follow and accept the windows prompts.

8.Select "Learning" option under carry out the tests menu display.

program Peugeot new keys-4.jpg

9.Select "Programming of keys";

program Peugeot new keys-5.jpg

10.The system will display key programming procedure when activation process is completed. Confirm to continue;

11.Confirm Unlocking the E.C.U program;

12.Manually enter the "Confidential code" (PIN Code).

program Peugeot new keys-6.jpg

13.The system is verifying the PIN code.If the code is correct, the built-in systems interface is ready for programming of keys;

14.Enter the key number to be learnt. The number of keys to be programmed cannot exceed 5.

program Peugeot new keys-7.jpg

15.Follow the screen prompt to switch off the ignition

16.Then switch ignition to ON within 15 seconds.

program Peugeot new keys-8.jpg

17.Key programmed, switch off the ignition and take out the key.

program Peugeot new keys-9.jpg

18.Switch ignition ON again and insert the next key in the ignition. Repeat the key programming procedure to program another key. When complete programming, the system will display keys that are programmed.

program Peugeot new keys-10.jpg

19.Follow the screen instructions.Check the handbrake is on. For an automatic gearbox, check the gear level is in position "P". For a manual gearbox, check that the gear level is in neutral;

20.Follow the re-synchronies the HF remote controls procedure to operate until the "End of key programming procedure" notice displays. Exit the program.

program Peugeot new keys-11.jpg

PS:

Another Lexia-3 xs Evolution (SP08-D), while the Lexia-3 above is SP08-C;

 

What are the differences for SP08-C Lexia-3 and SP08-D Lexia 3?

1. SP08-C Lexia 3 is made by original chip. It is more stable;

2. SP08-C Lexia 3 support Peugeot 307 models, but not good for Citroen C5, while SP08-D Lexia 3 does Not support Peugeot 307 and Citroen C5;

3. SP08-D Lexia 3 has one more cable than SP08-C Lexia 3.

08:00 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

23/04/2015

How to generate Ford Mondeo DPF with the VCM 2 IDS diagnostics tool

Ford comes with activate DPF (diesel particle filter). Active regeneration of these DPFs is employed when the exhaust temperatures are too irregular for a passive system to regenerate consistently. Here is an instruction on generating Ford Mondeo 2005 DPF and recoding datastream with Ford VCM 2 IDS.

Tools needed:

Ford VCM2 IDS diagnostic system V86 / V91 / V94 (newest version)

A laptop running Windows XP mode

Well install Ford VCM ii software

Connect the VCM II diagnostic tool with vehicle via OBD port or WIFI wireless connection

Select function tab, then press Powertrain >> Service Functions >> PCM

ford-vcm2-ids-generate-dpf-1.jpg

Check the function option under "Service Functions" menu, then click "EXIT" to select item for more information. Press the Tick mark on the right bottom.

ford-vcm2-ids-generate-dpf-2.jpg

VCM IDS will display detail vehicle information, engine type, VIN etc

Select control unit tab, select Powertrain >> Engine

ford-vcm2-ids-generate-dpf-3.jpg

Turn ignition to ON position

Select Equipped or Not Equipped Air Conditioning: Equipped

Select Equipped or Not Equipped EGR system: Equipped

 

Then come to the following program, the gray icons are valid, press B + (VOLT) and FRT (TEMP) buttons to turn to gray.

ford-vcm2-ids-generate-dpf-4.jpg

You will be able to view the live data stream

ford-vcm2-ids-generate-dpf-5.jpg

ford-vcm2-ids-generate-dpf-6.jpg

Press the icon on the up right corner, select "Save recoding group", press the tick mark

ford-vcm2-ids-generate-dpf-7.jpg

Enter the Filename model year and engine "MONDEO 2005 TDCI"

ford-vcm2-ids-generate-dpf-8.jpg

Enter Description: "GOOD RUNNING CAR"

ford-vcm2-ids-generate-dpf-9.jpg

Select recoding to save: 1, press Tick mark

Exit the program

Select "DataLogger" function

ford-vcm2-ids-generate-dpf-10.jpg

Select Powertrain >> Engine

Check the file saved

View the datastream recorded

Exit the Ford IDS software program disconnect the VCM2 system

http://vcm2.webs.com/

08:48 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

22/04/2015

Mb star C3 software download and problem solution

Super MB Star covers Benz Car, Bus, Truck, Sprint, Smart from 1989 to latest. Support Bens full system diagnostic, coding, programming, read/clear DTCs, and other special functions. Update on official website free for one year.

 

Here are some software usage problem and solution. Hope it can help you.

 

1.How to activate the MB Star C3 software?

A: After the installation in the VMware. There will be a file on the desktop named "How to setup your Star C3".

Please read the file carefully. And provide us your ID for us to calculate the password. You can activate the software with this password.

 

2.After the EPC was activated, every time I start the laptop, it needs activated again. How to do?

A: You can dowwnload a Driver Genius in your laptop, then the problem can be solved.

 

3.I am still experiencing problems with the EWA Keygen link so I cannot generate new start keys for the EPC + WIS. It prompt "The drive or network connection that the shortcut 'EWA Keygen.Ink' refers to is unavailable. Make sure that the disk is properly inserted or the network resource is available, and then try again." I have attached a screenshot for you to see the problem I am having. Please advise?

super-mb-star-c3-benz-ewa-wis-error-solution-1.jpg

A:Usually this problem is caused your EWA is deleted or unable to use for some reason. Please uninstall the anti-virus on your PC or do not install other software on the hdd. Please download this EWA KEYGEN: http://www.mediafire.com/download/8krwnrw0aw5ktcz/EPC_KEYGEN.rar, Please give me your LAN ID again, we will activate it for you again. Never use anti-virus software or install other software on the hdd. After done, The EPC starts + runs no problem.

 

4.1) The app icon displays in the EWA NET window but will not start,gives the following error ''SQL/Databaseproblem during server initialization''

super-mb-star-c3-benz-ewa-wis-error-solution-2.jpg

2) When i enter WIS, it show "WIS StartKey is invalid. Installation of the WIS database has Failed" what should i do?

 

For this two. All needs you open the WIS from the destop. And give us the EPC code for activation. 

 

Attachment about BENZ STAR C3 software download. You can free download your interested files. 

MB STAR C3 software download.jpg

http://mbstarseries.webs.com/

05:43 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)