topblog Ivoire blogs


How to update Bluetooth XTOOL PS2 GDS heavy duty scanner?

Xtool PS2 GDS is a hand-held diagnostic system covering most of gasoline heavy duty vehicles on the aftermarket. The Bluetooth PS2 diagnostic system can not only project basic diagnostic function, but support some special functions, such as oil service light, oil inspection, service mileage, service intervals and airbag. XTOOL PS2 system can be updated online. 


How to update XTOOL PS2 GDS heavy duty truck diagnostic scanner?

1) First of all, go to and login in to user center with User Name and password. 


2) Select “Download Center” option under “Navigation” tab 


3) Enter Download Center program, download the “Update Tool” 


4) Then download the software you need to update 


5) Save the update software to be downloaded to a certain folder 


6) Open and run Xtool “Update Tool-V* exe” setup on the desktop 


7) Follow the system prompt until the update tool installation is completed 


8) After installation finished, remove the SD card from the Xtool PS2 truck diagnostic tool, put the card into the SD card reader and then connect the SD card reader to the USB on your computer. 


9) Open the Xtool Update Tool on the desktop when the SD card has successfully connected with your computer 


10) Click the browse button to select the folder where you going to put the software winrar files. 

Click Confirm button and it will reads your PS2 serial number and the software. 


11) Select the software to be updated and click the “Update button” to update 


12) The PS2 GDS software update may take some time. Wait patiently until the update procedure is completed.

08:35 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


KESS ECU Tuning V2 2.12, 2.13 FW 4.036 Report and Review has extracted firmware V4.036 KESS V2 ECU tuning kit at the version V2.12 and V2.13. Following are kess information, tutorial and customer review gathering in order to have a better understanding of the Chinese clone KESS V2. 


NEW KESS V2 OBD2 Manager FW v4.036 Tuning Kit No Token Limitation


Software: V2.12, V2.13

Firmware: V4.036

KESS V2 ECU tuning-1.jpg

KESS V2 ECU tuning-2.jpg

Support one button click to charge tokens!!!


When token run over, just click this renew button on the main unit, then it will go back to 30 tokens. NO NEED change or desolder the chips, no need tokens programming. 

KESS V2 ECU tuning-3.jpg


How to install V2.13 software for KESS V2 ECU programmer with V4.036 firmware


Operating system: Win XP (most used) or Win 7


Language: English, German, Spanish, Italian, Portuguese, French


Free download KESS V2 FW4.036 K-suite V2.12, V2.13 software





We have tested the stability of K-Line, CANBUS, Tricore, J-tag and BDM before shipping out.

We confirm that our KESS does support EDC16 but DOES NO support EDC17 at present 

If you are a truck tuner, unfortunately there are only a few truck models available, but most of them VAN.


Here is our test photo: 

KESS V2 ECU tuning-4.jpg

Review from our customers:

1) I purchased one and it arrived within 7 days, tracking was included. I thought I has to replay about this clone kess v2 kit. I tested it on Renault Megane III valeo ECU at the first day, ID read fine, Writing ECU fine. 

Then I tested on a piaggio mp3 scooter using K-line.

ID read fine

Reading ECU was fine.

Writing ECU was fine.

See picture below..

KESS V2 ECU tuning-5.jpg

KESS V2 ECU tuning-6.jpg

So I am satisfied with the purchase. 


2) I have installed the Software version: V2.13. Firmware version: V4.036 with the help of the video in the webpage. It's important to strictly follow the instructions on the video. I have make a mistake at first install and got the EEFFACE error. I have send mail to vendor. Quick response by mail and now all works fine. Tested yet on EDC15C2 on table, read and write. Next week I will test on more ECU's. The Kess is more userfriendly than FGTech galletto. I'll buy also the Ktag from this seller. Good service and quick delivery.


3) I have done 15 cars without a problem and for 100 euro (V2.12).  I think it is a steal. As for the trucks section if I remember right it is open but cause I don’t have interest in trucks. I did not pay attention to this section. But I will test and report back.


4) I have installed V2_13 KESS and already tested on EDC15C2 in boot mode. Reading was OK, writing was OK as well. Tomorrow I have to do a DPF off of a Touareg 2.5l from 2009. I checked it is in the car list.


5) I tested in 4 cars for the time being and everything worked fine. I checked the truck section and can confirm that nearly all of the trucks are grayed out, except for Vans. I have not had the chance to test on 24v trucks Mainly Fords, Mercedes Sprinters are enabled.

KESS V2 ECU tuning-7.jpg

08:18 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


WIFI Scania VCI3 SDP3 Scanner v2.21 torrent on Win 7

WIFI wireless Scania VCI3 is a brand new diagnostic scanner designed by Scania to provide full maintenance for all Scania trucks, buses and other heavy vehicles or heavy duty engines based on CAN network system. Scania VCI3 comes with latest version of SDP3 (2.21) and USB license key (HASP key)


Software version: V2.21 



Operating system: Win XP/Win 7



English, German, Spanish, French, Japanese, Dutch, Persian, Polish, Portuguese, Swedish, Norwegian, Suomi, Turkish, Italian, Czech, Russian, Chinese.




Adjusting customer parameters, 


Conversions affecting the electrical system

Updating software in control units


Free download Scania SDP3 VCI3 torrent 


Free Download link 1


Free Download link 2:!XwxA0SCa!UPbsOjqYcs1vcuqGtgi8bWr0zKU...

Password: scania2015


How to install Scania VCI3 SDP3 scanner V2.21 on Win 7 (64bit)?

1). Install SDP3 V2.21. Do not plug USB dongle into computer. If you have plugged the USB dongle on that system before, you need to re-install the windows system and SDP3 software. 

2) Open HASP driver folder and install HASPUserSetup

3) Run cmd as administrator and type this: Hdwwiz.exe.  Press Enter to start the Add Hardware Wizard. Then click Next and select Install the hardware manually from a list (Advanced) then click Next>>select System device then click Next >> click on Have Disk >>Browse and navigate file to HL_Emu folder then vusb.inf. Click Open and confirm till finish.

4)  Double click on 2.reg file and confirm.

5)Open Multikey folder and depend on your windows ( 32 bit or 64 bit ) select one, and then run install.cmd

6)Run Scania USB Key.exe and confirm.

7)Wait until the system detects the new devices. 

8)Restart the computer 

05:10 Publié dans Blog, Shopping, Web | Tags : scania sdp3 vci3 | Lien permanent | Commentaires (0)