topblog Ivoire blogs


KESS V2 V2.13 firmware V4.036 Wake up error (fixed)

KESS V2 V2.13 firmware V4.036 Master ECU programmer no token limitation version “wake up error” fixed. 



When trying to read Bosch ECU EDC17 with KESS V2 Ksuite v2.13 firmware 4.036 ECU tuning kit, the software prompted “Wake up error”


Possible reason: 

1)TF connection issue 

Kess V2 fails to read out TF card program or the program in the TF card not working properly

2)Select wrong ECU type. 

Select wrong ECU type will cause wake up error either. 



KESS TF card communication failure 2 common occasions:

1) The four pins of chip on the PCB board are not soldered firmly

2) The chip is loosed or has been used long time 


Please follow the correct way to fix

1. Solder the chip one more to make it tightly connected to the PCB main board 

2. Clean up the shrapnel on the card slot with a brush 

3. If the card slot shrapnel is not flexible enough, lift up the shrapnel a little bit to make sure it can communicate well with the TF card 

4. Clean the TF card and then put it back to card slot.


If the kess v2 “wake up error” still exits, format the TF card then copy the software to TF card. 


1. Format TF card 

2. Contact customer service to send you the software in the TF card 

3. Unzip the file, copy and paste all 4 files to the TF card 



(Do not directly copy the zip rar. file to the TF card, do not create a new folder in TF card and copy and unzip it)


If the two above methods do not work, re-flash the CPU program, and then copy and paste the software to the TF card again. 


The “Wake up error” solution fits KESS V2 V2.10

kess v2 v2.13 firmware 4.036 Item No SP87-E

05:34 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


New Cheaper Star diagnosis MB SD Connect C4 with D-link

New Mercedes Benz MB SD Connect Compact 4 Star diagnosis system with D-link for WIFI wireless connection is available at more compatible price. 


Top 5 advantages of the new Star diagnosis SD Connect multiplexer:

1. Come with D-LINK WIFI Card, support Wifi connection (Dell format HDD)

2. More competitive price just needs €469.

3. Support both new Mercedes-Benz cars and trucks.

4. Come with one year warranty.

6. Two format available for choose: DELL D630 HDD/External HDD


Software version: 2015.07V

DELL D630 HDD/External HDD optional 

SD C4 Platinum edition HDD and SD C4 Platinum edition SSD optional 


Operating system: 

Dell D630 format HDD on Dell D630 PC

External HDD needs PC with CPU 2.0GHZ or above, 4GB memory or more.


Software including:

1. D-A-S / Xentry: 2015.07

2. W-I-S net: 2015.07

3. Electronic Parts Catalog 2015.07

4. ST Finder 2008: Part location finder

5. STARUTILITIES: the movement management system and self-test

6. SDMEDIA 2014

7. PL69

8. DAS Developer Mode 

9. Smart TAN Code calculator 





What’s the difference between the new SD Connect (Item No: SP100-B) and previous one (Item No: SP100-D)?

1)Share the same software and functions 

2)Made by different manufacturers

3)SP100-B new SDConnect Compact 4 with shell part design D-link WIFI card while SP100-D does not


New SD Connect C4 Star diagnosis multiplexer main unit firmware PCB board and D-link display: 



Previous Item No: SP100-D MB SD Connect 4 firmware PCB display:



How to set WIFI for New MB SD C4 diagnostic tool?

1. Disconnect the local area connection

2. Connect the SDConnect 4 with the car and start the engine

3. Connect to the wireless connections, please follow the instructions to set: 

click Configuration-MUX-Register/configure, under the "General information", select name "04" and then tick off "Wlan parameters, road", then set the following parameters: 

IP address:, 

Network screen:, Encryption: WEP / Hex, Key: aaaaaaaaaaaaaaaaaaaaaaaaaa (26 “a” in total), we have video tutorial, please click column "Video" to watch or contact our customer service to send you.

04:45 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


Lots of DIY coding with BMW Scanner v1.4.0 PA-Soft on Win 7

I am driving a BMW 320 E46 coupe 2005 and playing around with the cheap BMW Scanner PA-Soft V1.40 OBDII scanner a little bit. Here is my little walk-trough on working out the scanner and coding my E46 on win 7. 


Tools needed:

Cheap BMW Scanner cable with unlock PA-Software V1.4.0 

A laptop running Win 7 32 bit (Win XP/Win 7 64 bit)


If your BMW has 20-pin connector under hood, you properly need additional 20-pin to obd2 16 Pin Connector


Pre-coding installation:

I got a most detail document on set up the BMW Scanner 1.4.0 software on Win 7 32 bit (with free software driver download). Everything goes well with the instruction guide.

After well loaded the BMW scanner 1.4 software, plug the cable into the OBD diagnostic connector 

Run software and code BMW


Coding options:

This part I followed some instructions on official PA-Soft 1.4.0 thread in E46 forum. Some coding options I have not tested yet but the functions do work. 


ZKE Options:

- select "Coding data"

I am able to view lots of settings: Mirrors, One-touch functions, central locking functions, automotive locking, anti-theft system (DWA) etc. Tick the coding options and press “Write” button…


To activate the alarm optics without having a physical alarm:

-check DWA

-check the options with "optics"

*note if you have bits and pieces of the OEM alarm, you may enable those options


To activate an OEM alarm:

-check DWA

-check DWA interior sensor

-uncheck DWA interior sensor, rear (unless you have a convertible which has a front and rear interior sensor)

-check DWA tilt alarm sensor

-check the options with "optics" and "acoustics"


NOTE you must have all 3 (4 for convertibles) pieces to the alarm otherwise your car will throw a code. e.g. you have the siren and motion sensor but no tilt; your DWA will show a fault and will not arm. Siren will still go off if doors are breached.


To enable remote closing windows (Comfort windows):

-default "Opening (remote control)" is checked and "Locking (remote control)" is unchecked

-check "Locking (remote control)" to enable closing with remote

NOTE the lock button closes and unlock opens the windows upon holding of the key


To enable one click to unlock all doors:

-default "Selective" is checked. This allows one click of the unlock button of the remote to unlock the drivers door. A second click unlocks remainder passenger doors

-check "No" to unlock all doors with one press of the unlock button


To change the tilt of the passenger mirror when in reverse:

-default "Memory" is unchecked

-set mirror switch to passenger. The mirror will tilt to your personal position. 

-to set your position, have switch on passenger side, and adjust your mirror while in reverse gear


NOTE if "Memory" is checked mirror switch must be set to passenger for option to work. 

Switching to driver will disable the auto-tilt.


**note if "Memory" is unchecked mirror switch must be set to driver for tilt to work (by default it tilts to the maximum amount). Switching to passenger will disable the auto-tilt.


EWS Options:

To check the number of keys you have used:

-select key status

-you may also disable keys if you lost them from this menu as well


NOTE as you can see, I have two keys out there in the world from the previous owner as I only own two of them


To view live data:

-select live data


To disable the clutch switch:

-select "Coding data"

-select "Settings and manufacture settings"

-select Manual transmission


NOTE only for manuals. This allows you to start the car without having to depress the clutch


SRS Options:

To view live data about your airbags:

-select live data


To disable seat occupancy sensor:

-select "coding data"

-select "Equipment"

-uncheck "Seat occupancy recognition"

NOTE I haven't tired this as I don't need to nor have I installed aftermarket bucket seats


To disable seat belt light:

-select "coding data"

-select "Equipment"

-uncheck "Seat-belt buckle switch"

NOTE I haven't tried this myself as I always wear a seat-belt nor have a race harness。


IKE Options:

In the IKE menu you can change items such as service intervals frequency (ie. km/mi until next service), etc


LCM Options:

To enable or disable the DRLs (Daytime Running Lights):

-select "coding data"

-toggle the options for "running lights"


05:44 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)