topblog Ivoire blogs

25/09/2015

Encypt CAS lost ISN value, solved with VVDI Prog

Problem: 

Have an BMW X5 here with all keys lost CAS3+, read the CAS with rosfar as usuall

Tries to make a key from file and get these errors ”Detect encrypt CAS version. But CAS lost ISN value. Continue prepare key may cant start engine. ” and the second picture error “Can not find useful combine data, please check the EEPROM file.”

FullSizeRender-1.jpg

FullSizeRender-2.jpg

Working Solution:

This bmw eeprom don’t have enough data for combine test

For this car, you need read ISN from engine with other tool, the best working tool which can read BMW ISN from engine is VVDI prog made by Xhorse Company. 

 

The Procedure to Read BMW Engine ECU ISN with VVDI PROG

YouTube video: https://youtu.be/pJE9AhACibU

BMW-Engine-ECU-3.jpg

vvdi-prog-vvdi-prog-super-programmer-4.jpg

Open VVDI PROG software.

Select type: 3-ECU  Brand: BMW_F_ENGINE  Device: MEVD172(N20) 

Click “Wiring Diagram”

 

Wiring Diagram is open, it prompts NO.2 connector. 

NO.2-connector-5.jpg

NO.2 connector picture as follows.

NO.2-connector-6.jpg

Pull down the wiring diagram, attention: the left corner is NO.33 pin, and the right corner has pin, follow its pin number and order to connect the cable.

pin-number-and-order-7.jpg

This is real BMW Engine ECU 

real-BMW-Engine-ECU-8.jpg

All of pin numbers are marked as follows.

pin-serial-number-9.jpg

Next, to plug the cable into VVDI PRO 

connect-the-cable-10.jpg

Firstly, connect red power cables, there are 2 power cables, one is No.1 pin, one is NO.22 pin.

power-cable-11.jpg

2-power-cables-12.jpg

Next, connect GND cable, it is NO.10 pin.

GND-cable-13.jpg

Finally, connect blue CANH cable and yellow CANL cable.

 

This group of cables are connected well.

connected-well-14.jpg

This is Bootm line.

boot-line-15.jpg

Open a hole on Engine ECU and locate the pin position by following the wiring diagram, then use Boot line to point at this pin and to read data. 

pin-position-16.jpg

Note: an external power adapter is necessary for VVDIprog, because it reads Engine ECU.

 

Close wiring diagram on VVDI Prog 

 

Select “New Create”

 

Select “Read”

 

Wait until the data is read out successfully. 

 

Select “Save” to save data.

 

Last note: 

If BMW CAS4+ all key lost, firstly read CAS data then Engine ECU data, when it asks for ISN code, just load Engine ECU EP data to generate dealer key.

 

Done. 

Hope this helps.

24/09/2015

How to update Ford VCM2 IDS to V97 (V97.1)

Ford VCM2 IDS software has newly updated to V97 (23/09/2015). Here is the instruction on updating your Ford IDS to V97.1. 

 

NOTE: IDS V97 is compatible with Ford VCMII scanner SP177-1, SP177-C, SP177-C1 and SP177-C2. Do not work on other VCM2. 

 

Software version: IDS V97.1

Operating system: Windows XP/ Windows 7 on VMware (recommended)

 

Free download Ford IDS V97.1 software 

http://www.fordservicecontent.com/Ford_Content/IDS/IDS-97...

You can download form the link directly or download from Thunder (enter URL to download directly), because the software is huge. 

Ford-VCM2-IDS-V97-1.jpg

How to update VCM2 IDS to V97?

1.Have old V81, V91 IDS installed 

1) First install C81 Calibration files and then V86 IDS

2) Then install V91 IDS, if the software displays 3 day trial prompt, then continue to install IDS V96, otherwise quit software installation and change another laptop to re-install software 

3) After well install V96 IDS, install IDS V97 software 

4) Update VCM2 firmware (following instructions below)

 

2. Have IDS V96 installed 

If you already have VCM2 IDS V96 installed, then directly install V97 IDS and update VCM2 firmware. 

 

How to update Ford VCM 2 scanner firmware?

1) Press the power button on VCM2 scan tool main unit 

Ford-VCM2-IDS-V97-2.jpg

2) Long-press on the power button, connect VCM2 with power supply, wait for all 4 indicators turn on, then release the button. Then connect VCM2 with computer via USB cable 

Ford-VCM2-IDS-V97-3.jpg

3) Run IDS software, software will prompt to update firmware. Wait the update procedure is done.

Ford-VCM2-IDS-V97-4.jpg

Ford-VCM2-IDS-V97-5.jpg

4. Restart computer when firmware update is completed. Connect VCM2 kit with vehicle to start diagnosing or programming functions. 

Ford-VCM2-IDS-V97-6.jpg

23/09/2015

How to install MPPS V13.02 software driver on Win 7?

MPPS V13.02 EDC16 ECU Tuning Remap Chip tuning CAN Flasher is default to be installed on Windows XP operating system, but some have achieved it on Win 7. Here is the instruction on installing Mpps v13.02 on Win 7. 

 

The instruction fits MPPS V13.02 K+CAN USB cable (SE74, SE74-B)/SMPS MPPS interface with a Driver disk

MPPS-cable-and-disk-1.jpg

MPPS-cable-and-disk-2.jpg

If the driver CD is broken, you can free download MPPS V13.02 driver software here:

http://down.obdexpress.co.uk/mpps-v13.part1.zip

http://down.obdexpress.co.uk/mpps-v13.part2.zip

 

Instruction:

Open driver CD or software file 

Install MPPS13.02.exe setup 

Select software Language (multi-language avaliable), click OK

MPPS-V13.03-install-on-win7-3.jpg

Install hardware wizard, click Next 

MPPS-V13.03-install-on-win7-4.jpg

Select destination C:, click Next 

Click Next 

Click Installation to install driver 

MPPS-V13.03-install-on-win7-5.jpg

Click Finish when installation is completed 

 

If MPPS software prompt “MPPS Firmware Upgrade” message, it is normal when MPPS cable is not plugged in or the driver is incorrectly installed 

Click Exit

MPPS-V13.03-install-on-win7-6.jpg

Now plug the MPPS USB cable with computer 

If win7 fails to automatically install driver, install the driver manually 

MPPS-V13.03-install-on-win7-7.jpg

Go to Start>> Computer>>right click Properties>> Device Manager>> Amt Flash>>Update Driver Software…

MPPS-V13.03-install-on-win7-8.jpg

Select Browse my computer for driver software 

Browse file to C:MPPSDevice Driver 

MPPS-V13.03-install-on-win7-9.jpg

Click Next 

If the system prompts “Would you like to install this device software”, click “Install”

MPPS-V13.03-install-on-win7-10.jpg

Installing driver software is completed 

In windows 7 you will need to run MPPS as administrator, otherwise, software will not open. 

MPPS-V13.03-install-on-win7-11.jpg

Right click MPPS v13.02 software on desktop, click Properties 

Select Compatibility 

Tick Run the program as an administrator, click OK

MPPS-V13.03-install-on-win7-12.jpg

Open MPPS V13.02 software on desktop 

If you try to run MPPS not as administrator or without the cable plugged in you will see following screen 

MPPS-V13.03-install-on-win7-13.jpg

Installation is completed. Start tune ECU with the MPPS software.

http://www.obdexpress.co.uk/service/smps-mpps-v50-edc16-c...