topblog Ivoire blogs


Xentry PassThru - Questions and Answers

There are a lot of Xentry PassThru questions frequently asked and answers given by users and folks in Hope it helps.


All PassThru versions works as good and as same as SDconnect C4 units?

- for xentry, i check all diag files are identical with open shell.
- for das, it is not as complete as openshell with sd4. see note above.
passthru limited to obd2 vehicles only, pkw,transp, smart.
- passthru device can't be used with vediamo and dts monaco.



Could you explain this a little more: "install block check keys to daimler server"?

from old crack:


C:Program FilesMercedes-Benzxentryfusokoeclipseplugins
Rename File

now its other version number
also block starkey center
host file:




This is pass thru version is there a other version for diagnose for pass thru device???

so 1 dvd diagnose other dvd for programming?

only 1 dvd mate. Sdflash folder for programming is include in it.
the using of xentry passthru version is like the xentry open shell version only it is using passthru devices.



Xentry Internal Error (3.17)-3.175 "no access authorization code" after xentry diagnose while onlineCOPY C:ProgramDataLicDirlic_key_2.dat to the desktop, rename it to lic_key_2.x4711, and make this file READ ONLYMOVE it back into the directory C:ProgramDataLicDir. make sure the lic_key_2.dat file IS NOT read only while lic_key_2.x4711 file READ ONLY...



DAS license 0 day, how to do?

extract and copy this to dasbin:

DAS license 0 day error fix for passthru.rar


Xentry Passthru Model covered?

Pretty much all can vehicles. Works great with Xentry vehicles. So I would say Xentry Passthru is good for 2006 and up.

Passthru Models are only from EURO5 Vehicles (for Europe)




Tips and guides for DAS/Xentry users: How to use Xentry Passthru

Look here:

Newest DAS/Xentry: 07.2018

Look here:



Ford/Mazda IDS 109 Download: 100% Tested with VXdiag VCX Nano

Free Download Ford/Mazda IDS software version 109 for VXdiag VCX Nano:


Ford IDS 109 download:

Mazda IDS 109 download:


No password!

100% tested by Allscanner

Works perfect with VXdiag VCX Nano Ford/Mazda




  1. Programming & Installation of new ECUs……….worked!
    (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.)……….worked!
  2. Live Data-stream with Recording & Playback Functions for main ECUs……….worked!
  3. Read & Clear Diagnostic Trouble Codes (DTCs)……….worked!
  4. Set, Adjust or Remove Speed Governors……….worked!
  5. Automatic vehicle recognition……….worked!
  6. New Software Re-flash for Existing ECUs……….worked!
  7. All Other Dealer Functions……….worked!
  8. Steering Angle Resets………………….worked!
  9. Guided Fault Finding………………….worked!
  10. Program New Keys………………worked!
  11. DPF Regeneration………………worked!
  12. Brake Bleeding………………………………..worked!
  13. Injector Coding……………………………………..worked!



Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Topic :how to use Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Here you are:


copy the immo information from a cluster to another

make the mileage follow with the immo information



Audi a4 2001


Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA-USB programmer


Original cluster:

The Jaeger cluster barely works

audi-a4-2001-cluster audi-a4-2001-cluster-1 audi-a4-2001-cluster-2


read the pin code from both the Instrument and adapt it to the vehicle


What to do on pin 21 and 22 on the chip:


- With ECU programmers:

Eprom.set type,mcu,hc12,read,save.

eprom,set type,mcu,hc12,file,load,write.

Buy yourself Xprog-M programmer, Carprog, UPA-USB.

Pin 21 and 22 jumper after programming or wait 10 minutes.


- with Digiprog3:


Eprom,set type,mcu,hc12,read,save.

eprom,set type,mcu,hc12,file,load,write.



Eeprom HC12 read and write to the other counter:



(Write down the exact ALWAYS old / incorrect Mileage)

The diagnostic port is in the driver's footwell. Turn the ignition

on a vehicle. Connect plug ST16 the diagnostic port and the



Select the program: cars / trucks - AUDI - MM 4 / 99- DIAG.

The DIGI PROG II shows you the old / incorrect Mileage.

Enter the new / correct Mileage and confirm this.

Should be then after programming on the speedometer 999999 KM give

The old / wrong KM value again so that the speedometer again the old /

false indicates KM. Now you build the speedometer and break it to the

see board. Solder the green and black wire to the same color marked

Arrows at. Now connect the blue and the green plug with

the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)

Now select the program: cars / trucks - AUDI - MM 4/99 HC12.

The DIGI PROG shows you the old / incorrect Mileage. Enter the

new / correct Mileage and confirm this with the hook.

Now shows you the DigiProg II 5 min wait. Remove the connection

between the DigiProg and the speedometer, wait 5 minutes and build the speedometer

again. Alternatively, for 5 min. Wait, you can also like in the image on the

next page shows the pins 21 and 22 bridges.


Here necessarily the board from any power supply (Digiprog,

external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer

Immediately reinstall.


OBDexpress disclaimer:


Thanks for all tech support from members’ share at