topblog Ivoire blogs

10/11/2016

How to solve Consult 3 plus can't see no vehicle in list

My Nissan Consult 3 plus can't see no vehicle in list. And the same situation when selecting "diagnosis(One system)", there is only Renault!
In "SuB", can not view all brands, only button "unit setting"/"country selection" and "vi/mi registration".
++

My Nissan Consult 3 plus can't see no vehicle in list. And the same situation when selecting "diagnosis(One system)", there is only Renault! In "SuB", can not view all brands, only button "unit setting"/"country selection" and "vi/mi registration". ++ Problem solved! Consult 3 + won't install with Nissan channel if Renault Clip installation is detected! It's the reason why i can not choose brand installation (Nissan/Datsun... If clip is present, channel Renault is choosing by default without choice). I will try later installing CP+ before clip abd will see if both application can be run in the same pc. Then i was suggested to “go back and check diagnostic tool.ini in the first line is channel, you can change it there to select Nissan , Datsun , and the other one With 0,1,2 or is it 1,2,3 cant quite remember ,anyway , it has nothing to do with CLIP . It will be the same without it . another thing is , when you couldn't select these buttons , you could detect automatic vin where you cannot select buttons, click each vehicle and wait two seconds, on one it will come alive and then for all of them. another way is to remove quickly usb and put it back very fact , then will be alive , it is because of a block in the software . really all the J2534 have access for ECU Programming , just like NERS.”

Problem solved! Consult 3 + won't install with Nissan channel if Renault Clip installation is detected! It's the reason why i can not choose brand installation (Nissan/Datsun... If clip is present, channel Renault is choosing by default without choice). I will try later installing CP+ before clip abd will see if both application can be run in the same pc.

 

 

Then i was suggested to

“go back and check diagnostic tool.ini

in the first line is channel, you can change it there to select Nissan , Datsun , and the other one With 0,1,2 or is it 1,2,3 cant quite remember ,anyway , it has nothing to do with CLIP .

It will be the same without it .

another thing is , when you couldn't select these buttons , you could detect automatic vin

where you cannot select buttons, click each vehicle and wait two seconds, on one it will come alive and then for all of them.

another way is to remove quickly usb and put it back very fact , then will be alive , it is because of a block in the software .

really all the J2534 have access for ECU Programming , just like NERS.”

This article is from :http://obd2expresscouk.blogspot.com/2016/11/consult-3-plu...

09/11/2016

Guide to program Hyundai vvdi remote key with Xhorse VVDI2

Hyundai remote key programming successfully! With Xhorse VVDI2 key programmer.

 

Tools preparation:

Vvdi tools (Xhorse VVDI2)

vvdi-tools

A new vvdi remote key and the original Hyundai key

vvdi-remote-key

Here are the remote generation steps...

 

Step 1 - chip information collection via VVDI2 xhorse

Install the battery for the new wirless remote key

- take out the pcb on the remote controller

- install the battery

 

vvdi2-vvdi-key-tool-program-hyundai-remote-1 vvdi2-vvdi-key-tool-program-hyundai-remote-2

Generate wireless universal remote into chip signal collector via VVDI2 v1.2.2 software; VVDI2 automatically detect the chip

 

vvdi2-vvdi-key-tool-program-hyundai-remote-3

vvdi2-vvdi-key-tool-program-hyundai-remote-4

vvdi2-vvdi-key-tool-program-hyundai-remote-5

Press the remote control buttons and the LED will keep flashing (it means that: it’s coming into the collection status)

vvdi2-vvdi-key-tool-program-hyundai-remote-6

Signal acquisition is successful when the LED flashes rapidly

 

vvdi2-vvdi-key-tool-program-hyundai-remote-7

vvdi2-vvdi-key-tool-program-hyundai-remote-8

 

Information collection is complete. Now, ready for decoding and chip copy.

 

vvdi2-vvdi-key-tool-program-hyundai-remote-9

vvdi2-vvdi-key-tool-program-hyundai-remote-10

Step 2 - chip decoding and copy by vvdi2 v1.2.2

Put the chip with a battery installed into the remote control

vvdi2-vvdi-key-tool-program-hyundai-remote-11

Put the original car key into VVDI2 device for identification

vvdi2-vvdi-key-tool-program-hyundai-remote-14

Click on Start copy in VVDI2 interface

vvdi2-vvdi-key-tool-program-hyundai-remote-12

To collect information in the car and put the collector into VVDI2 (because we have been collecting data, it’s ok to put the collector into vvdi2)

vvdi2-vvdi-key-tool-program-hyundai-remote-13

vvdi2-vvdi-key-tool-program-hyundai-remote-15

Put the original key into vvdi2 key programmer again

Connect to the network, to begin decoding online

vvdi2-vvdi-key-tool-program-hyundai-remote-16

Chip decoding success!

vvdi2-vvdi-key-tool-program-hyundai-remote-17

Put the the the collector (vvdi remote key) into vvdi2

Chip copy success

vvdi2-vvdi-key-tool-program-hyundai-remote-18

 

Step 3 - remote control generation 

Try to start the car with the new copied key, after chip copy success

It can start the car but the remote cannot work properly

 

vvdi2-vvdi-key-tool-program-hyundai-remote-19

vvdi2-vvdi-key-tool-program-hyundai-remote-20

Ready to generate remote control

Use vvdi2 control generating function to generate the remote control

Put the new key into vvdi2 programmer

Finish vehicle info selection and click on Generate Remote Control

vvdi2-vvdi-key-tool-program-hyundai-remote-21

Complete

vvdi2-vvdi-key-tool-program-hyundai-remote-22

Use special equipment to program the remote

vvdi2-vvdi-key-tool-program-hyundai-remote-23

Xhorse wireless universal remote can copy a chip after regeneration as remote control, in the new equipment is the vvdi key tool (will add this function)

Done!

This article is from :http://blog.obdexpress.co.uk/2016/11/09/xhorse-vvdi2-program-hyundai-remote-key/

 

08/11/2016

How to update kess v2 2..8 software

This software update program can use in :SE87:KESS V2 OBD2 manager tuning kitSE87-C: Kess v2 4.036 firmwareSE87-E: Kess v2 3.099 firmwareSE87-K: KESS V2 Truck versionSE87-CK: V4.036 Truck KESS V2
Kess v2 2.25/2.28 installation steps:

Step 1 – install K-Suite v2.25

Run K suite software and install K-Suite 2.25

software-and-install-k-suite-2-251

Accept the license agreement

Select installation language to go on

software-and-install-k-suite-2-252

Install usb driver

software-and-install-k-suite-2-253

always click on Next until installation completes

software-and-install-k-suite-2-254

Ksuite installation success.

Ksuite language: English, German, Spanish, Italian, Portuguese, French

software-and-install-k-suite-2-255

Step 2 – disable network

Disable all network connection

software-and-install-k-suite-2-256

Step 3 – setup Ksuite properties

Go to Ksuite properties

Click on Find targets, then delete the “help” folder in C:Ksuite

Copy another “help” folder in disk E: to C:Ksuite

Close all windows

 

Step 4 – install & setup software for USB device

Select install USB device software automatically

After finishing the installation, go to Computer management

Select USB device

software-and-install-k-suite-2-257

Step 5 – Ksuite v2.25 read BMW E90 ecu

Run KSUITE on desktop

It’s Kess v2 ksuite v2.25

software-and-install-k-suite-2-258

Here we test Kess v2 on BMW E90 MED17/MEV17 ECU reading

 

software-and-install-k-suite-2-259 software-and-install-k-suite-2-2510 software-and-install-k-suite-2-2511 software-and-install-k-suite-2-2512 software-and-install-k-suite-2-2513 software-and-install-k-suite-2-2514 software-and-install-k-suite-2-2515 software-and-install-k-suite-2-2516 software-and-install-k-suite-2-2518 software-and-install-k-suite-2-2519 software-and-install-k-suite-2-2520 software-and-install-k-suite-2-2521

BMW e90 reading ecu OK. Save data.

 

Step 6 – setup Ksuite v2.28

Delete “Setup 2.25” on Desktop

Again, open Ksuite properties

Click on Find targets,then delete all files in C:Ksuite except the “help” folder

Copy all files in the Ksuite 2.28 zip file to C:Ksuite

Delete the Ksuite 2.28 zip file

Then open K-suite app on Desktop

It’s ksuite 2.28 version now

kess-v2-ksuite-v2-28

Ksuite 2.28 can read BMW e90 ecu id like Ksuite 2.25 above

kess-v2-v2-28

Done!

http://blog.obdexpress.co.uk/2016/11/08/update-k-suite-ke...