topblog Ivoire blogs

05/11/2015

Solution for Toyota Techstream not displaying AHC pressure values

My personal issue goes as follows:

I am the original owner of a 2006 LC with AHC. I have 168K miles on the truck and it has been a true workhorse. I recently purchased a cheap MINI VCI on obdexpress.co.uk to troubleshoot an issue on my Tundra and thought I'd poke around a bit on the LC. Specifically I wanted to look at the AHC pressure values. Based on what I'm reading I'm probably way overdue for rear springs and torsion bar adjustment. 

 

The cable seems to work with Techstream V10.10.018 on all of my vehicles but it isn't reading the AHC pressure values on the LC. I saw in an old thread that I needed to pick LX470 when connecting to the vehicle otherwise I get a "selected system is not available" message. 

 

I also read that on a cable check it was necessary to read from pin 7 and as you can see in the attached image when connected to the LC pin 7 is red. When connected to another vehicle with the same cable pin 7 is green but 6 & 14 are red. I don't know what to think about any of that.

 

Does anyone have any thoughts as to what may be the issue?

 

Cable: http://www.obdexpress.co.uk/wholesale/mini-vci-for-toyota... 

Current Output:

current output-01.png

current output-02.png

Solution:

I'm getting ready to do an AHC lift with some coil spring spacers, adjustment on the sensors, and rear shock extenders. I get all the parts installed but I have the techstream cable and CD ready to go.

09:50 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

How to use BMW V5 CAS4+FEM+F15 CAN Filter

BMW V5 CAS4+FEM+F15 CAN Filter is a professional mileage programmer for BMW CAS models. CAS4 CAN-filter can change the mileage for BMW F01, F07, F10 and X3 2011-2012 (with motorola processor 9S12 XEP mask 5M48H / 4M48H – SC 66 7095 CAG).

BMW CAS4 CAN Filter-1.jpg

BMW CAS4 CAN Filter, FEM and F15 etc wiring diagram/pinout:

CAS4 CAN-Filter for BMW pinout-2.jpg

CAS4 CAN-Filter for BMW pinout

BMW Fxx CAN filter V5 (Support all F-series CAS4, FEM, BODY, ECU)

CAS4 Connection diagram-3.jpg

CAS4 Connection diagram

F3x IKE-4.jpg

F3x IKE

F3x with MOST-5.jpg

F3x with MOST

BMW 2014 X5X6 (F15F16) CAN Filter-6.jpg

F15 CAN Filter Connection pinout

BMW 2014 X5/X6 (F15/F16) CAN Filter

(II. Do not need to remove the BODY-ECU, do not need to be installed inside into the bodyecy)

 

(Remove CANBUS Inductor)

 

Brown---CAN out H

Green---CAN out L

Yellow---CAN in H

Blue---CAN in L

Red---12V

Black—GND

F15 IKE-7.jpg

F15 IKE

Brown---CAN 2 H

Green CAN 2 L

Blue---CAN 1 L 

Yellow---CAN 1 H 

Red---5V 

Black---GND

F15 instrument filter-8.jpg

F15 instrument filter

F18 instrument wiring-9.jpg

F18 instrument wiring

Brown---CAN2 H

Green---CAN2 L 

Yellow---CAN1 H

Blue---CAN1 L

Red---5V

Black---GND

F35 IKE-10.jpg

F35 IKE

BMW MINI F56-11.jpg

BMW MINI F56

F20 F3x EFM-12.jpg

F20 F3x EFM

F20, F30, F35 FEM-13.jpg

F20, F30, F35 FEM

 

How to use the CAS4 BMW CAN Filter?

To change KM in these cars you need to install BMW CAS4 CAN filter inside CAS4 module and later change data in eeprom 35160 located in instrument cluster.

 

Open and remove CAS4:

Open and remove CAS4-14.jpg

Open and remove CAS4-15.jpg

Open and remove CAS4-16.jpg

Open and remove CAS4-17.jpg

09:39 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

04/11/2015

IDS program used ECU for Ford Focus 1,8 Flexifuel 2009 FoMoCo ECU ESU411 7M5112A650AAD

Purpose:

Is it possible to do Immo off or make this type of ECU virgin?

 

This info for the car:

Ford Focus 1,8 Flexifuel 

2009 

FoMoCo 

ECU type: ESU411 

Partnumber: 7M5112A650AAD

Delnr301078_1.jpg

Delnr301078_2.jpg

Delnr301078_3.jpg

Answers/solution:

You don’t need a virgin. You can program even a used ECU with VCM IDS without any problem, only need outcode for programming. 

 

Where to get VCM IDS plus outcode for programming?

Recommend OBDexpress.co.uk, VCM IDS plus outcode package sale for €317+shipping, at: 

http://www.obdexpress.co.uk/wholesale/rotunda-dealer-ids-...

VCM IDS plus outcode for programming-4.jpg

Q: How to use Ford Outcode / Incode calculator?

A: When you place an order from us, we ship you a WS Dongle(USB Key), at the same time, we send you a software driver (or you are free to download it from the product page "Related Download Files"). After receiving the WS Dongle(USB Key, you connect WS Dongle(USB Key) with your computer USB com port and then run the software driver, once finish setup, it’s ready to calculate the incode with outcode.

 

The following 3 pictures display how to use Incode calculator:

incode-5.jpg

incode-6.jpg

incode-7.jpg

10:42 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)