topblog Ivoire blogs


Why Digiprog 3 wins?

Lots of new odometer correction tool flooded into the market. But you’ll find that topics of Digiprog 3 china clone never end in the automotive forums. People keep interest in and give good reviews of this tool. Most Digiprog 3 purchased is very satisfying!


Digiprog 3 odometer corrction tool


Look here.. users share their OK and K.O. experience. And here, Laura collected all for you. Hope it helps.




Audi a1 works (depending on software number)

Audi a2-obd -ok

Audi a3-repair 999999 in dash with digiprog

Audi A3 2010 by OBD OK

Audi A3 2002 obd2 is ok

Audi a3-2001-vdo-obd ok

Audi a4 2001-2005-obd ok

Audi a4 8e b6 2004 obd ok, use 2 minutes

Audi a4 2007 obd dash read ok write ok/ecu make-it via touran edc16 write 2 times to change.

Audi a4 2009 3.0quattro obd ok

Audi a4 2005-2009-obd ok

Audi A4 2010 Work

Audi a4 2012 obd ok and fast

Audi a5 2013 obd ok

Audi a5-2010-obd ok 15 min

Audi a6 c5 obd

Audi A6 2002 ok after some effort.

Audi a5 2009 3.2L obd ok 30min

Audi A6, 2009 work OBD, 4-5 minute.

Audi A6 2010 dash via obd (takes a while to find code but ok)

Audi A8 4.2 tdi 2008 Dash OBD OK 2min

Audi S3 2002 obd2 is ok

Audi TT 2002 obd2 n8 is ok

Audi q3-2010-obd ok 15 min

Audi Q5 2.0tdi 2010 by obd …20-30min

Audi Q7 2012 20 sec by obd work ok

Audi Q7 2007 —>OBD work

Audi q7-2008-obd ok

Audi tt hc 12 plug ok


BMW I82017 work..unit from ebay

BMW E46 2004 —> 35080 Clip Work

2001 bmw x5(e53) sure ok and also range rover with same dash. no problem.

have to take dash out and solder on back of board.

can use BMW 35080 option.


Corolla verso 2007 ok with luck


Chevrolet Montana obd ok

Chevrolet Cruze 2011 obd ok

Chevrolet Aveo 2012 obd ok

Chevrolet Corsa obd ok (after unplugging battery for a few secs)

Chevy suburban 2007 ok if you disassemble dash and read 95080 using eeprom menu then calculate manually. Will not do it by OBD. Be sure to include Km or Mi, original mileage, desired mileage and hours.


Citroen DS3 93C66 new release DS4 24C16

Citroen C3 / DS3 new releases

Citroen Jumper 2007

Citroen: DS3 C3 C66 Case3: hc12x new release

Citroen C3 programming via Tacho & Box

Programming Citroen C5 via Box & Cluster

Citroen C5 Programming 2003 via chips

Citroen C8 programming via Tacho & BSI

Citroen Saxo New diagnosis

Citroen Picasso NEC Tacho & Box via Micro & Chip

Citroen Relay Van Chip 95040 Chip Programming

Citroen Xsara 2000/2002 NEC programming via BSI & Tacho chips

Citroen Belingo 2003/2004 Cluster and BSI Programming

Programming Citroen Belingo HC08 Tacho via Micro

Citroen C3 programming via the chip

Citroen C5 New software programming via cluster & BCM

Programming Evasion Citroen via puce

Citroen Relay programming via chip

Citroen Xantia programming via chip

Citroen Xsara programming via chip

Programming Citroen Xsara via BCU & Tacho


Ford transit 93c76 eeprom ok

Ford fusion hc 12 plug ok

Ford mondeo 2008-ond ok

Ford focus hc11-ok with plug

Ford focus 2006 obd ok

Ford focus 2004-2010 obd ok

Ford s-max 2009 obd ok

Ford Fiesta 2012OBD OK (fiesta 2005 obd not ok)

Ford fiesta 2008-2010 red screen obd ok

Ford Fiesta HCS12 —> ST48 Work

Ford Mondeo 2008 Full Colour Fis 24C16 – – – OBD diag Read – 0km ,Write – OK!

Ford mondeo 2010 visteon dash with 9s12 read ok write ok via 4 wires on pcb

ford mondeo 2004 st51 read ok/write ok

Ford Bantam 2006 need nec programmer

Ford connect 2008 obd not! fvdi obd, read km but not change! dp3 ,conector 48, 9S12read and write km!


Fiat ducato 2014 obd dash ok (ecu 95640) but nyo 2015 suport


Galaxy 2008 new model by the OBD ok


Honda crv 2002 dash (68hc912)

Honda civic ep3 type r 2002 eeprom OK


Hyundai I10 (No connection i10 mcs12hy64 to digiprog ….if its 24c08 use plug 1)

Hyundai Terracan w nec, adapter st59, 100% ok, working


insignia 2011 obd ok 1min

Land Rover Discovery 4 24c16 tacho – ok

Range Rover sport 2010 24c16 tacho – ok

Range Rover evoque 2013 via obd ok


Mazda b2500 – b2900 ok


Mercedes w204 c250 2011 obd ok (Just put through as ezs, it will block sync and do dash)

Mercedes w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok

Mercedes w210 obd

Mercedes w211 and do obd

Mercedes w219 works as w211 just flashes dash obd

Mercedes W251 R350 2010 ok OBD (no sync problems no can filter needed)

Mercedes class B W246 use direct in OBD

Mercedes vito 638 2003 OBD ok

Mercedes W211. Cluster is no problem via OBD. For EZS, need a cable called HC12.

Mitsubishi galant 2006 93C46 ok

ercedes Vito W638 2003 OBD ok

Mercedes class B W246 direct use in OBD ok

2003 Read and Save Group the Mercedes EEPROM via EEPROM / MCU ok


Nissan navara , pathfinder motorola ST48 by points OK

2011 Nissan micra 1.5 tekna 93c66 eeprom use honda accord c66 option on digiprog same algo by desoldering and using clip st01 to read and write no need to remove needles chip on back of board


Opel Vivaro 2013 —> EEPROM Clip work 93c76

Opel Astra H —> 35080 Clip Work

Opel astra h 2006 – m35080 – work

Opel Astra 2000 obd ok

Opel insignia 2013 obd –OK

Opel Insignia 2014 —> OBD Work perfect

Opel Corsa, the digiprog working.

Opel Corsa c and astra g. Read and out new mileage in. When press tick, hold trip button and ofometer will flash. When digi says check value, release button and disconnect battery for 10sec–> Job done


Peugeot 307 2002 —> Work, Dash —> NEC (New ST59), BSI —> HC12

Porsche panamera 2014 by eeprom 95640 work ok


Saab 9-3 2009 HCS12 ok

Seat MII 2013 —> OBD Work


Skoda Superb (3t) II 2009y only by obd less then 5min

Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok

Skoda Octavia 2010Y 1.6TDI cluster via obd

Skoda Octavia 1z 2011 OBD ok

Skoda Fabia MK2 2009 diag no problem

SKODA Fabia 2009 obd ok.

Skoda Roomster 2009 —> Diag work Perfect


Toyota yaris(2011), remove and clean chip to read/write, need luck

have to look first which eeprom on circuit my experience with some toyota that they use a small 93C46 wich is not in the menu


Volvo xc90 2007 dash ok by soldering

Volvo xc60 2009 obd ok

Vauxhalls Vivaro2011… 93c76…. All good… read and write..

93c76 option not available under Renault Traffic so use Vivaro or maybe try Renault Master as has 93c76 option that seems as though it would work, have not tried, read ok but didn’t i write chip…

Volkswagen Eos obd2 ——ok

vw eos 2007 —> Diag obd2 work

vw polo, seat ibiza 2007 magenti marelli motorola ST48 by points OK

vw polo 2001-2005 vdo obd ok

vw polo trw plug ok

Vw fox 2007 hc912 by solder point and ST48 work

Vw touareg 2004 obd ok

Vw Tourag 2013… read ok but write failed

VW Tiguan 2007 —> OBD OK

vw tiguan 2010-2011 OBD ok

Vw AMAROK 2012 obd ok 1 min

vw bora all obd ok

vw jetta all obd ok

vw jetta 2012 work obd

vw t5 obd ok

vw t5 ecu edc 16 ok 50%50

vw touram dash obd ok

Vw Golf 4 BOO via OBD ok and Audi a4 boo crypto too

Vw Golf 4 without problem!!!

Vw Golf 5plus by obd -visteon dash read ok write ok

Vw Golf 6 plus 2010 work ok

vw Golf MK6 2012 works OK

Vw Golf 6 work good till 2013 year

Vw Golf 6 plus 2010 Works ok

Vw Passat 2013 obd..ok

Vw passat 2007 obd ok

Vw passat 2008 via obd-dash read ok write ok/ecu read ok write ok 5 min.

Vw Passat CC 2.0tdi 2010y done by obd

Vw passat 2006 tdi dash & ecu obd OK

Vw passat 2001-2011 obd ok

Vw passat 2011 work obd 5 min

Vw passat 2012 work obd

Vw passat cc 2012 work obd

Vw Passat b5 2003 tdi all ok

VW Caddy 2013 jet menu makes Golf 6 2012>

VW Touareg 2004 OBD ok

VW Polo, Seat Ibiza 2007 Magneti Marelli Motorola ST48 by OK points

Seat Leon 1M 2000 2002 and 2003 via OBDII no problem

T5 2004 dash & ECU via OBD -read? / Writing ok 10 seconds. ECU EDC16 read write ok 7 minutes

Sharan 2001 via OBD-lu? / Writing ok

Skoda Octavia 1z 2011 OBD ok

Skoda Fabia 2009 OBD read? / Writing OK

Skoda Fabia 2010 OBD, read? / Write OK after second try


reads 9s12 mcu with cables 48 and 51


Complicated with the EPROM of Peugeot 508 2012…

Need open dashboard, and Bsi.

Peugeot 508 have eproms. 95080 and 95256.

Read them, then put them here

Peugeot 508/508 new version

Peugeot 106 diagnostic

Peugeot 206 Programming Jaeger via Micro

Peugeot 206 M2002 NEC All new programming modules via chip

Peugeot 306 VDO Diagnostic Cluster

Peugeot 307 chip programming via Box & Tacho

Peugeot 307 HC12 Microphone Programming

Peugeot 406 Programming Jaeger via Micro

Programming Peugeot 406 Sagem via chip

Peugeot 406 Valeo Box Programming by Box & Cluster

Peugeot 406 VDO Diagnostic Cluster

Peugeot 406 VDO 2000/2001 Cluster + BCU

Peugeot 407 Programming by Tacho & BSI

Peugeot 607 Programming VDO via Cluster Box +

Peugeot 806 Jaeger / Programming Magneti Mareli via Micro

Peugeot 807 Programming by Tacho & BSI

Programming Peugeot Boxer via chip

Programming Peugeot Partner via chip




Cars that Digiprog 3 FAILED to do:


Audi A3 2014 dash 8V , obd not connect


BMW X1 2013 failed… no bmw after 2002 can go by obd… have to program the 35160 chip in cluster and the cas4 (or fem?) module.

or cluster + can filter cable behind cluster to block cas. but digiprog can’t program 35160


BMW 325 e90 or x5 e53 no luck with digiprog via obd2. Cas3 just says no connection or just give me a 1349652 miles which is wrong.


GMC yukon 2001 cannot do via obd


Hyundai I10 9S12HY64 cannot work… Digipro can’t read D flash memory , so it cannot read and write this kind of mcu like Hyundai eon,Hyundai i 10 so use UPA USB can do it.


Chevrolet Cruze 2012 obd didn’t work. remove BCM next to left foot passenger seat you’ll find 24c16 ok


Mercedes W245 digiprog can’t doby obd.

use cluster plug or program chip.

first set to 999999km. then install cluster and put the car on contact for 1minute. then program cluster to any value.

It’s the same for w169


Mercedes Sprinter 906 need to program ezs (cannot with digi , but XprogR270 programmer working no issues)

or use can filter. (yes they exist)


Nissan pathfinder 2000 c56 eeprom, cannot read. Had to do it with TU. Very disappoint couldnt do no 9s12 with digiprog.


Opel astra g, corsa c, zafira a, never have success to do with digiprog by obd


Opel insignia 2010 obd not work.


VW polo 2012 johnson control nec 95320 kill checksum dashboard error … (x-tool or another good tool can fix it)


VW Golf 6 2013 OBD NOT OK


Volvo xc60 obd 2013 won’t go. Only does till 2010


Note: for models with no luck, perhaps obdstar x300m is a good choice. Anyone can try it. i don’t have this. But the reference may help you if you fail with DP3

The best user buying guide of digiprog iii incl Digiprog 3 for sale(best price), update, manual, review, FAQ, car list… at here :


How to program VW Polo 2009 4th IMMO NEC+24C32 Key with Lonsdor K518ise via OBD

This steps guide of  how to use  Lonsdor K518 key programmer program VW Polo 2009 4th IMMO NEC+24C32 Key via OBD.

Key information:

Original key: 3-button folding remote key

Frequency: 433MHz

Chip type: Special ID48 chip (TP23)

Device to program: Lonsdor K518ISE key programmer





Connect K518 host with vehicle via OBD diagnostic socket

Select Immobilizer->VAG->4th Immobilizer->Identify Immo type



Lonsdor K518 identified immo type: 4th IMMO




K518 detect vehicle part number and immo type



Select NEC 24C32



Then Backup EEPROM and save data




Select Read Immobilizer data



Lonsdor K518ISE read vehicle information: VIN, CS, PIN, key number and key ID



Select Make Dealer Key



Push card slot on K518 main unit from right direction

Insert new key to be programmed into card slot





Select Key Learn



Enter key number to be programmed (keys that will start vehicle )



Insert key and turn ignition on one by one

I.E, Dashboard shows 1-2 means 1 key has been learnt, 2-2 means 2 keys have done



Program success.



Test remote and star car





Digiprog3 V4.94 Clone odomter Correction Feedback

Loooooooog post here ,here is  Most Comprehensive Digiprog3 reviews ,Writing this post for Digiprog3 V4.94 mileage correction feedback, thanks real users' real test reports.


This post content:

Part 1: 2017 year feedback 

Part 2: 2016 year feedback 

Part 3: 2015 year feedback


Here we go one by one.

Part 1: 2017 year feedback of Digiprog3 V4.94 Clone

VW Bora 2008 micronas + 24c32 via OBD OK!

VW Jetta 2012 Nec + 24c64 via OBD OK!


worked on Mini cooper S clubman 2008 (r56) (For CAS OBD, For Dash R270)


twingo 2003 vdo. cable 34. worked fine.


Porsche 997 gt3 2008 obd ok.


Car 2014 VW Tiguan Diesel OBD2 OK DIGIPROG 3 CLON


Fiat grande punto 2012 obd with (fiat doblo 2007->) read ok write ok


Audi a3 2011 with digiprog works fine, use the diag -2012 option. of dash goes black. then do the same again.


2014 US VW Jetta GLI VDO DSG Ok by OBD

Suoer Fast If Engine Running

Set TPM of After Reset Service & Clear Codes

Disconnected Batt Reconnected Than All Dash Lights, I had to turn steering wheel straight,

left then right and straight again then test drive and went back to normal.

I used Golf 6 Option.


Digiprog done Audi a3 8p 2003 Ok


ford transit 2006 24c16 via st1 read ok write ok

Fiat Doblo 2017 --- OBD OK


Fiat 500 2012 via obd2 -> OK

Fiat 500 2017 obd OK

I test my on vw grupe and work perfect until golf 7

Peugeot 106 plug43 --- Okey


toyota lancruser 2010 cs86 ! on eeprom ok


I done a Ferrari California with Digi 2min obd


I did a Ferrari 458 with digiprog. the mileage in ferrari cluster is a very easy system. The tools only needs to read the eeprom, we know digiprog can do this witg other cars without problem, so if it reads the correct mileage then i dont see much risk.

(And it is a clone, but the software is same as original tool)

But the mileage is also in the ecu of ferrari.


Can read eeprom 95320 (gateway of Audi A6 C6) by Digiprog 4.94 clone by clips SOIC8?

and save to *.bin file.


- Can correct opel astra g 2011, Astra g is 93c56 (2001), Astra h is 35080 (2007), Astra J is in Bsi (2011) , all work with digi prog fine


- change the mileage of a mercedes clc 2009, Digiprog is possibe.


- Question: Can I connect to pc to transfer eeprom data from and to digiprog?

Answer: if you FTDI chip inside, you can, if you don't have ftdi chip you can't connect to PC


- nissan nv200

yellow - bdm

brown - gnd

green - reset

white - 5V

use qashqai HCS12 works 100% see attached pics for pinout from backside of cluster no needle removal quick job




Part 2: Digiprog 3 V4.94 mileage correction feedback in 2016 year:

  1. Mercedes W251 R350 2010 ok OBD

no sync problems no can filter needed


  1. Digiprog do all Golf 4 without problem!!!  Golf 4 BOO via OBD OK


  1. BMW X1 2013 - no bmw after 2002 can go by obd, you have to program the 35160 chip in cluster and the cas4 (or fem?) module.


or cluster + can filter cable behind cluster to block cas. but digiprog can't program 35160


  1. dp3 clone will do a 2010 Audi A6 dash via obd, it will takes a while to find code but will do it.


  1. w219 works as w211 just flashes dash obd


  1. Mercedes class B W246 use direct in OBD digiprog 4.94
  2. To read and Save mb w211 2003 cluster eeprom, need to desolder it.
  3. Digiprog 3 4.94 clone can do Mercedes E550 2004 via OBD but will put ezs to 9999999..
  4. 2004 touareg obd ok
  5. 2014 Audi A1 with the 4.94 version ok
  6. Aveo 2012 OBD ok digiprog clown


2012 Chevrolet Aveo obd on the new type cluster or the old type as per picture

  1. vw polo, seat ibiza 2007 magenti marelli motorola ST48 by points OK
    nissan navara , pathfinder motorola ST48 by points OK
    AUDI A3 2010 by OBD OK
  2. Audi TT 2002 obd2 n8 is ok work
    Audi S3 2002 obd2 is ok work
    Audi A3 2002 obd2 is ok work

vw t4 2002 diag obd t4 1998  write ok

  1. Vw fox 2007 hc912 by solder point and ST48 work
  2.  volvo xc60 obd -2010 ok
  3. Skoda Octavia 1z 2011 OBD ok
    Mitsubishi galant 2006 93C46 ok
    Mercedes vito 638 2003 OBD ok
    Saab 9-3 2009 HCS12 ok
    Audi A6 2002 ok after some effort.
    A6 OBD told me it was m73 D09.
    A6 M73 OBD gave me the 999999 checksum error.
    The A3 repair 999999 with st41 left me wondering what to do with those two extra cables but AUDI MM 4_99 HC12.pdf sorted that out!
    Both st41 and st48 has wrong colors but with pinout sheets you will do fine!


  1. digiprog can do a 02 chevy avalanche, remove the dash and use ST47 with this. Use Tahoe on the menu.
    Won't do the hours though, that has to be done manually with eeprom menu as S95P02.


Note: that is the only way, you can't do it with OBD with a Digiprog. Dash out in 60 seconds, takes all of five minutes to remove the board and solder to it and program it.


  1. Audi A4 2010 Work

Audi a4 2007 obd dash read ok write ok/ecu make-it via touran edc16 write 2 times to change.

Golf 6 plus 2010 work ok


  1. Mondeo 2010 visteon dash with 9s12 read ok write ok via 4 wires on pcb.


  1.  digi can do gmc yukon 2008, you have to disassemble the dash and do by eeprom. Use Hummer H2 2007- 95080 chip, make a backup first.


  1. To use correction mileage hyundai I10 to digiprog3, no connection i10 mcs12hy64 to digiprog ....if its 24c08 use plug 1.


  1. Correct audi a5 2012 ok


  1. 2012 audi Q7 20 sec by obd work ok
    2014 porsche panamera by eeprom 95640 work ok
    version 4.94


  1. Vw Tourag 2013... read ok but write failed :/



Peugeot 307 2002 ---> Work

Dash ---> NEC (New ST59)

BSI ---> HC12

  1. Audi Q7 2007 --->OBD work


  1. Skoda Fabia 2009 OBD write ok

Skoda Fabia 2010 OBD write OK after second try


  1. I did Some cas by diag but most give unknown version.If Digi gives you wring milleage press * and other milleage Will be shown.Btw cas 2 Will not work by obd (maybe by dashplug or wires direct to cas.Both not tested by me, if i remove i prefer direct by prog.


  1.  by obd all golf 6 digiprog 3 clone work good for me till 2013 year.

I also range rover with same dash, soldering on back of board, no problem, you have to take dash out and solder on back of board. U can use BMW 35080 option.


  1. Fiat Grand Punto 08 by OBD works 100%, but you need to use menu Doblo.


  1. Skoda Fabia MK2 2009 diag yes no problem


  1. fiat ducato 2014 obd dash ok

ecu 95640 unknown version,but nyo 2015 suport


  1. Test VW UP work great OBD. i confirm vw up 2012 goes with digi 4.88 2-3 minutes the dash goes black after calibration no panic igntion off -on


  1. dp3 clone can do 2010-2011 vw tiguan odometer via OBD.


  1. sharan 2001 digi 4.94 /write ok / vdo dash


  1. T5 2004 dash & ecu via obd write ok 10 seconds.Ecu edc 16 read ok/ write ok 7 minutes


  1. audi a4 8e b6 bj. 2004- Very good, 2 minutes


  1. 2011 Vauxhalls Vivaro... 93c76.... All good... read and write..93c76 option not available under Renault Traffic so use Vivaro or maybe try Renault Master as has 93c76 option that seems as though it would work, have not tried, read ok but didn't i write chip...


  1. opel opel insignia 2013 obd --OK


  1. for the keyless go mondeo, take it out and mileage corrected direct, no need to remove eeprom.


  1. Hyundai Terracan w nec, adapter st59, 100% ok, working


  1. my experience with digi 4.88

Chevrolet Corsa obd ok (after unplugging battery for a few secs)

Vw AMAROK 2012 obd ok 1 min

opel Astra 2000 obd ok

chevrolet Montana obd ok

chevrolet Cruze 2011 obd ok

chevrolet Cruze 2012 obd didn't work. remove BCM next to left foot passenger seat you'll find 24c16 ok


  1. digi 4.94 ford mondeo 2004 st51 read ok/write ok


  1. Procedure: merceds A 160 klasse 2005 goes with digi

You can do dash with dash plug.

But first make good Back-up of eep.

But you need ezs too, you can block communication by putting 999999 in dash put it back in the Car ignjtion on and ezs wil take 999999.

Than you put ori dump to dash and change like you want.


  1. Opel Astra H ---> 35080 Clip Work
  2. passat obd ok

06 focus obd ok

09 s-max obd ok

05 fiesta obd not ok

digi 4.94 passat 2013 OBD ok


  1. For Caddy 2012, you need to choose another car in the menu, choose VW T5 2012 Diag, Also you can choose Golf.6, the both are ok mate just plug and play.


  1. digi 4.94 golf 5plus by obd -visteon dash read ok write ok. It's ok can do it without any problems don't worry just plug and enjoy.carprog clone not work on visteon dash.digi is ok.


  1. Q: the ST 59 works with all digis or only the one delivered with it and wjere it can be ordered


  1. Pinout for 01 bmw x5 e53

Color chart included to cross over to digi.

35080 chip, you need to erase first or use a new chip, don't think digi will erase them. 

  1. Q: Which cable do I use to do an 06 accord without removing the needles?? I have this pic which I pulled from this site?

A: ST47, but you only use 12345 & 8


Q: Today has arrived my Digiprog3 from Ali. I tried, to connect to my car via OBDII (Seat Leon 1M, year: 2000) but it says with both option (diag, diag bosch, diag ECU): no connection. The cable was connected right, i'm sure.


Yesterday, I tried an Opel Corsa D with my digiprog, it's semms like working.

Today, I removed my Leon's dash, pictures attached.

Now, I'm sure, it's a VDO dash. How can I connect directly to the odometer, with my digiprog?

t's strange. I connected to the Corsa the OBD cable, and read the old KM.

But, the main question is the Leon.

I find on the motherborad, the memory chip: 93C86

If I connect with the clip cable to the 93C86, is there a chance to write that?

Attached another pictures, about my accessories. FYI, my cable is not bad because with an Opel Corsa, the digiprog working.

A: You can't use st16 to do a corsa D

Corsa d old with digiprog wow

Desolder read and see what value it gives

FYI, 50% of digi not work on is yanhua digiprog


  1. Q: Mercedes W212 how to change with tacho diag or EZS ??

A: For this car use ezs option!

The facelift model is not possible. so don't try.

If you have digiprog 4.88 you also can do the full color screen of the w212. if you have 4.94 then you can do only black/white screen.

After correction do 'fehlerspeicher' to delete errors in dashboard.

Do 'assist manager' to delete service history.

if it is a diesel engine most times you get dpf error. and the car will drive max80kmh. until you reset dpf.

Remember: if you use the ezs option. digiprog will program 999999 miles in ezs. this way it blocks ezs-tacho synchronization.

it's better to use a canfilter, this way ezs will have old mileage. of you use can filter you must use the 'tacho diag' option.


54 Q: how to work with the service mode?

A: make-it via obd. first time blocked on 0000 but second try it works. Second try I mean disconnect completely en retry, ignition off.remove obd plug put it back ignition on and try.when is ok you will see 0001-0002.....not stopped on 0000.



Q: I have a toyota yaris(2011), and I wanna change the mileage. But when I try to connect the Digiprog with the eeprom, it says "can't find chip".

I'm using connector 1, and keep the chip incircuit.

De chip is a 93c56, SMD chip

What do I have to do?


A: You have to look first wich eeprom on circuit my experience with some toyota that they use a smal 93C46 wich is not in the menu i wil give you an exempel i had to do a corolla verso 2007 in the menu it says if i remember 93c66 ichoose 93c66 i couldnt read "chip not found"i i looked closer it was a smal 93c46 wich is not in the menu of verso avensis i choose another option in the toyota menu with 93c46 i think it was celica and it could read chip the morality of the story look first wich chip itis on the board and from there work with it . good luck

dont remove nothing toyota always read on circuit look if there is an condensator close to the eeprom and shunt the legs. Don't matter toyota or any brand always safer to remove for read/write eeproms



Q: Can digiprog work on this golf 7 dash - any suggestions what is ideal tool for this type of cluster via obd

A: Smelecom can do golf 7 vdo dash but only certain versions. If it's Johnson control then no tool can do


Fail list:

1 Hyundai I10 9S12HY64-use upa usb ...digiprog can’t do it, Digipro can’t read D flash memory , so it cannot read and write this kind of mcu like Hyundai eon,Hyundai i 10 so use UPA USB can do it.


  1. Not suport audi A3 2014 dash 8V , obd not connect. And for genuine tool Very hard to do this Car.


  1. dont try to do 2010+ volvo with digi, if you are lucky it only wont work, otherwise...


  1. - Dont try to use digiprog to read cas it wil end with faillure dead cas, get the r260 red clone it works perfect.if you look in youtube under digprog3 hc 12 or 11 and st 53 you wil see it.


Part 3: 2015 year feedback:

  1. Digiprog 4.94 tested ok results:


  • For VW, Audi, Skoda vehicles:

VW Tiguan 2007 ---> OBD OK

VW Passat 2007 ---> OBD OK

Passat 2013 obd..ok.

Seat MII 2013 ---> OBD Work

passat 2011 work obd 5 min

passat 2012 work obd

passat cc 2012 work obd

jetta 2012 work obd

Skoda Superb (3t) II 2009y only by obd less then 5min

A6, 2009 work OBD, 4-5 minute.

golf mk5..ok

Volkswagen Eos obd2 ------ok

Skoda Roomster 2009 ---> Diag work Perfect

vw eos 2007 ---> Diag obd2 work

Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok

SKODA Fabia 2009 obd ok. fabia -diag-read ?-write ok. (digi4.94)

Golf 6 2012 obd ok

Passat 2011 menu dash diag -2012 read ok/write ok /3 minute.

audi a4 2010 obd ok, audi a3 2010 obd ok

no problem with audi a3 for now 2011 and 2010 doing ok by obd

passat 2006 dash work

golf 2007: dash and dsg ok

300 m 2009 ok

jetta 2014: ok test Many Time always ok

tiguan 2009: ok test Many Time always ok

wrangler 2012 ok

Golf 4 MM Just open dash en look voor 24C** it takes 2 minutes

passat 2011 work by OBD

Vw Jetta 2013 take golf 6 on car list. Work fine 2 minutes

skoda superb 2011 nec+24c64 obd works fine.



-Works 100% polo 6N 2001 - diagnostic -ST16 - doesn't show old mileage but writes perfect - on cluster display where mileage shows while writing it shows error for about 5sec then check written value on DigiRemember to reset service reminder.

VW Tiguan 2011 OBD no problem, takes about 10 minutes


VW evoque 2012 work by OBD


  • For BMW vehicles:

BMW E46 2004 ---> 35080 Clip Work


  • For Ford vehicles:

Ford Fiesta 2012 ---> OBD OK

Ford Fiesta HCS12 ---> ST48 Work

2012 Ford Focus - 95320 - by ST1 work ok



  • For Mitsubishi:

For read & write correct Mileage use

Mitsubishi Outlander 93C86 V2 ---> Work Perfect on Peugeot 4007 2012


  • For Mercedes Benz:

w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok.

E39 m5 dash done with digi using st47

MERCEDES w210 E - DB 4_99 with Stecker 10 , ok!


  • For Opel:

-Opel Vivaro 2013 ---> EEPROM Clip work 93c76

-Astra J 2011 work by OBD.

-  astra g 2001 write ok 10 seconds

- astra h 2006 - m35080 - work

-Opel Insignia 2014 ---> OBD Work perfect

  • For Fiat:

Fiat Grande Punto EVO 2011 dash-- obd OK.... fiat doblo

Fiat Ducato 2012 work perfect OBD

Fiat Doblo 2009 ---> OBD Work perfect 1 sec. Job


8)Other models:

Galaxy 2008 new model by the OBD ok

Successfully made chevrolet orlando like a opel insignia


Digiprog  read/write 35080 for 100%.


Range Rover Evoque 2013 via obd ok


Nissans: 2002 Altima 93C66 OK in circuit with Murano; 2001 Xterra 93c56 OK unsolder with Patrol


Toyota RAV 4 2007 ---> eeprom clip 93c56 work



- Made : sportage 2012

Swift 2014

Ranger 2010

Prado 2006

Runner 2006

Navarra 2012


All eeprom on board ...i did NOT try obd

- salvage Yard

nitro 2009 ok

patriot 2013 ok

2015 xtrail does work with digiprog 4.94, chip 93c86 worked a treat

volvo s80 2008+ work good 10min.



Thanks all real user of digiprog3 clone.

Thanks to put all the real test report of digiprog3 clone here, which will be very helpful to the new users.