topblog Ivoire blogs


Honda HDS Key Programming with HDS HIM diagnostic tool

To add one new key/Keyless transmitter, you need:
1. Immobilizer Mater Key Blank or Immobilizer Valet Key Blank 
2. One programmed ignition key (master or valet) for the vehicle
3. Vehicle key code
4. PCM code
5. Honda HDS HIM diagnostic tool with immobilizer programming software
 HDS 3.101.015 (!! cheap honda hds cable only for diagnosis)
The HDS is required for registration of the immobilizer keys. Programming the immobilizer also programs the keyless transmitter.
Use the HDS with Honda key blacks to add a key or keyless control unit, storing the transponder code of the new key in the memory of the control unit.
6. Condor XC-MINI key cutting machine

Make sure the market, the date, and the time on the HDS setup screen are correct. 
Select the F12 key in the upper right corner to get the Set-up Details screen.
Make sure Market is set to USA. 
Select the time display in the lower right corner to get the Date/Time Properties pop-up window.
How to program a new key to Honda with Honda HDS scanner:
1) Use an appropriate key blank and the key cutting machine to cut a new ignition key.
2) Connect the Honda HIM diagnostic system with vehicle via OBD socket 
3) Insert a programmed ignition key into the ignition switch 
4) Turn ignition ON
5) Run Honda diagnostic system personal computer (pc) software and come to iN screen 
6) At the screen prompts, enter the VIN and the odometer reading, then verify the correct date and time.
7) Select “IMMOBI” from “System Selection” Menu
8) Select “Immobilizer Setup” from “Immobilizer Test Mode” Menu
9) Select Add and Delete Keys 
10) Select Add 1 Key 
11) Select Begin to Add 1 Key 
12) Follow the HDS screen prompts, if your HDS is not logged in to the iN, you willhave to enter the PCM code you have retrieved from the iN Immobilizer Code Inquiry to proceed. 
13) When adding keys procedure completed, turn ignition OFF
14) Exit HDS software and disconnect Honda HIM HDS scan tool from the vehicle
P.s. This is the Honda HDS pocket tester in use.


OBDSTAR DP PAD Program &Diagnosis Tablet Funtions

Japanese and Korean vehicles are distributed widely and receive good reputation all over the world. Therefore, OBDSTAR DP PAD is created in response to the proper and conditions. It is a convenient device, combining Android system, immobilizer, diagnose and special function, which closely follows the global trend and greatly meets the demand of users. In addition, abundant and powerful maintenance database and car testing video have realized easier operation and real success. Furthermore, Remote guide strengthens the communication between end users and technicians, without worries about after -sell service. 

Immobilizer+ odometer adjustment+ EEPROM/PIC adapter+ OBDII+ ABS+ TPS+ SRS reset+ TPMS(low tire)reset+ Steering angle reset+ CVT learning/Value reset+ EPB+ Oil/service reset+ Battery matching+ Diagnosis(Japanese and Korean serials)

Read and clear fault codes;
Clear key memory;
Program keys, proximity keys, smart key, flip keys;
Program after-market and OEM keys;
Display live data;
Component actuation;
Read keys from immobilizer memory
New ECU programming;
New mechanical key number programming;
Vehicle identification key programming;
Reset ECU& Reset immobilizer;
New remote controller programming;
Immo PINCODE reader;
Mileage adjustment via OBD;
With full and strong database for the most important vehicle makes;
VCI diagnose
One key upgrade via wifi 
Remote assistance
Report center
EEPROM chip read and immobilizer initialization;
EPB(Electric park brake);
Oil/Service reset;
Battery matching;
SRS reset
TPMS(low tire)reset 
Steering angle reset
CVT learning/Value reset
EEPROM/PIC adapter


Creator User Manual Of How To update Software

Here I will tech you how to update Creator products (incl Creator C500,C310,C330, C100,C110 etc) step-by-step here .

Note: This Update method is applicable to all Creator products!

Here is the procedure:

Step 1. Setup Update tools

Download the update tool from official 
Double click the [Setup file] to setup the tool. Operate follow the instructions, and finish to setup.
After finish setup, there will be a icon of scanner in desktop.

Step 2. Download the software

Download from official website
Note: C100 and C110 software is only fix SN is C1XX 002000 02 or later
You can find the software what you want.

Step 3. Run the update tool

Double cleck the update tool icon and Run the update tool and Operate in accordance with photographs
Used the USB cable connected to scanner and PC, if connect success, the software on pc will shown as below

Click [Update] button.

Cleck red rang , you can change the path , and find the updatefile which recive.
Select update file and click [open] button.
Into the upgrade interface, wait for the end of upgrade
Do not power off during upgrade!
Do not Plug or Unplug USB tools during upgrade!

Step 4. Start Update

Waiting for a few minutes. The software will update the scanner tool.
Finish Update.
When the update is finished , the screen on PC will show as below.
If update success, the software will display [Update success!];
if update fail, it will display [Update fail! Try again].
Press [finish], the scanner is already updated, and you can unplug the scanner from PC.
This article is from the leading online exporter of OBD2 Scanner: