topblog Ivoire blogs

17/05/2017

ELS27 FORScan Scanner PCB Rework as the Original to enable SLEEP function

This is the how-to’s of ELS27 FORScan scanner PCB rework as the genunine ELS27 to enable the SLEEP function.

 

If you have a ELS27 FORScan scanner from China, you need rework the PCB same as the genuine first.

 

ELS27-FORScan-scanner-clone-pcb-1

 ELS27-FORScan-scanner-clone-pcb-2

In clones, not all components are sealed, so besides the CAN protocol is not any work. If the missing solder components, the K-line likely will work perfectly:

 

Detect vehicle on-board network configuration

Read and reset Diagnostic Trouble Codes from all modules

Reading of modules’ sensors’ data

Run test diagnostic procedures

Run service procedures

 

If you the function above is what you need, a ELS27 OBD2 from China will be a good investment coz the genuine ELS27 is three times as expensive as the clone one. Professionals tested the ELS27 clone many times and verified it’s functionality.

 

This is ELS27 FORScan scanner car list:

All Ford, Mazda, Lincoln, Mercury vehicles that can be addressed by supported adapters. It is 99% of models after 2000 and around 92% of models after 1996 (the year when OBD2 became a standart in USA).

 

 

But the SW CAN definitely not works that on the board there is an error, so sometimes PCB rework is necessary.

 

This is the original PCB of ELS27 FORScan scanner

genuine-ELS27-pcb-1 genuine-ELS27-pcb-2

 

 

If someone needs SLEEP function, do as follows:

ELS27-FORScan-scanner-sleep-function

 

Please note that by posting 300k goes to the R26 which should unsolder!

By default, the function is disabled in the very STN. For activation we send one by one command in the terminal:

STSLX on, on

the ATZ

STSLCS

should give approximately the following:

the CTRL the MODE: NATIVE

PWR_CTRL: the LOW the PWR = the LOW

the UART the SLEEP: OFF, 1200 s

the UART WAKE: the ON, 0-30000 us

the EXT the INPUT: the LOW the SLEEP =

the EXT the SLEEP: the ON , the LOW the FOR 3000 ms

the EXT WAKE: the ON, the HIGH the FOR 2000 ms

the VL the SLEEP: OFF, <13.00V the FOR 600 s

the VL WAKE: OFF,> 13.20V the FOR 1 s

VCHG WAKE: OFF, 0.20V the IN 1000 ms

If someone is willing to take the risk, you can try without divider. That is, instead of 150K solder jumper and everything, and to do the above in the terminal. I did that on the first board, but does not activate in the STN, respectively my adapter did not fall asleep. But it did not burnt. Wait adapter is not for me, so I can not check.

To see how the adapter is asleep, you must send the computer in Standby mode.

Instead 300k and 150k can be used with a pair of nominal ratio of 2: 1.

 

 

15/05/2017

BMW ICOM NEXT A Reviews

Here is some custome‘s reviews on the new BMW ICOM NEXT A  frequently asked questions and answers (FAQs) of icom next a are attached here. 

 

What are the advantages of an ICOM NEXT vs the old ICOM?
My current “old” ICOM works fine, just wondering what I’ll gain from upgrading?

 

-it is faster in F and G series ..

– and supports gigabit Ethernet too to be future proof, there currently is not gigabit Ethernet protocol defined yet for autos. Also it has USB3.0 instead of USB2.0 and a better wifi card. 

 

 

Does ICOM NEXT have WiFi functionality ? WiFi I mean wireless connection between ICOM head and laptop

 

Yes. There are some software checks in place for certain operations (eg, programming) that will instruct/prevent user from continuing until they swift from WLAN to directly connecting.

 

 

Does anyone have updated part numbers for ICOM Next A?

 

Received Icom Next 2 days ago OEM part number has no change –

81 31 2 360 883

 

 

Which ICOM Next should i get for 2009 Mini R56.

 

ICOM NEXT A is enough.

Only for checking the cars you don’t need a ICOM.

 

 

Who has really tested the new BMW icom next? is really good? Please your opinion?

 

Unless you have lots of spare money, I would not rush to buy it just yet, wait for a few more firmware releases first, you can read a few documents on issues with ICOM Next and using ISTA and ISTA-P and BMW’s official workaround is “Use ICOM”. So at the moment you really need both.

 

 

Has somebody tested successful the Icom Next A with an Icom B to flash a CIC or CCC with WinKFP?

 

– I`m using ICOM NEXT A constantly, with E series software pack ( inpa-ncs-winkfp) and F series ( Esys-bmw-aicoder) and obviously ISTA , and no issues . All working good.

 

 

Any good site to recommend for a working icom next?

 

I got mini from http://www.obdexpress.co.uk/wholesale/bmw-icom-next-a-b-c...,  have had no issues with daily use using multiple ICOM NEXT A’s on E series with standard tools (don’t forget to reserve head first in itool radar) or Ista, F series with Ista, even BMWTIS

 

 

How to update ICOM Next A firmware?

 

In order to solve your incident, please apply the following steps:

Note: DO NOT UNPLUG the {ICOM Next} from the {OBD II} jack after an update via {ISTA}, a web interface or an emergency software update.

The {ICOM Next} starts with flashing green SYSTEM {LED}s. After about 10 seconds it shows red {LED}s for about 2 minutes. After this, the {ICOM Next} reboots due to a firmware update.

If the {ICOM Next} {LED}s remain red for more than 10 minutes, or if the {ICOM Next} is unplugged directly after an update, please carry out the following procedure:

1. Please ensure that ALL of the following prerequisites are satisfied:

1.1. You require a {USB} 2.0 or {USB} 3.0 flash drive. ({USB} 1.x flash drives are not supported).

1.2. The {USB} flash drive must be formatted with a {FAT32} file system.

1.3. A minimum of 60 {MByte} free space is required on the {USB} flash drive.

2. Navigate to “{C:ProgramDataBMWISPIdataTRICICOMNextICOM-Image-03-14-08}”.

ProgramData folder is hidden by default. In that case, you have two options in order to access the file or the folder:

– change the settings directly in the Windows Explorer (“Tools => Folder Options => View => Show hidden files, folders or drives”)

– or enter the whole path into the Windows Explorer’s address bar and press enter.

3. Copy “{ICOM_Next-rootfs-010002.tar.gz}” to the root directory of the {USB} flash drive.

4. Copy “{ICOM_Next-app-010008.tar.gz}” to the root directory of the {USB} flash drive.

5. Disconnect the {ICOM Next} from the power supply.

6. Plug the {USB} flash drive into the {ICOM NEXT}.

7. Press and hold the button pressed on the {ICOM Next} and connect the {ICOM NEXT} to the {OBD II} jack of a vehicle.

8. Keep the button pressed. The {ICOM NEXT} starts with all {LED}s glowing red. The {LED}s stay red; some may flicker orange/yellow. Keep the button pressed.

9. Keep the button pressed. After about 4 seconds, all {LED}s turn orange/yellow. All {LED}s now glow in the same colour.

10. Release the button and then press it three times within five seconds. The {LED}s glow or flash red and orange/yellow again.

11. Wait: This procedure may take several minutes. Do not disconnect the {ICOM NEXT} as long as any {LED} glows red.

12. After about 5 minutes the SYSTEM {LED} turns green again. The {ICOM NEXT} has been updated and is ready for use.

13. If the issue is not solved:

13.1. Please submit a support ticket via the {OSS Cockpit}.

13.2. Please provide the “{restore.log}” from the {USB} stick.

IMPORTANT: When the software update is complete, the {ICOM NEXT} needs to be connected to the dealer’s network in order to be reconfigured.

All previous settings are lost during the update. If there is a “{user.settings}” file on the {USB} flash drive, it will be applied after the firmware update.

 

 

Enjoy!

 

10/05/2017

Launch X431 scan tool, Launch M-Diag, Launch Easydiag, which best?

Launch X431 or Launch Easydiag? 

 

Lauch x431 is better than easy diag. If you really want one cheap with some bi-directional control a DS150e chinese clone is ok but you’ll need to set it up on a laptop.

 

I’d recommend Easydiag and Vlads Software 1 year update . It gives you id say 95% of what real x431 xpro3 can , i’m speaking about basic functions that original would have that cracked easydiag to xpro3 wouldn’t have 1 or 2 .

you can make easydiag xpro3 with dongle and software for 1/10th cost of what original x431 xpro3 costs .

 

with easydiag and vlad’s software, you can do actuator testing on most vehicles yes but limited only to what the vehicle u are testing has .

 

i have Original Launch X431 full and easydiag Vlads work 1 to 1

this Delphi ds150 e is full shit not have special function only live data and errors

I have for each car brand dealer unit !!!

before 1 year i work with TEXA this device is full full shit !!!

buy Launch! It works very well !!!

 

 

So, Launch x431 wins! For launch x431 scan tools, 2017 launch x431 v 8 inch tablet should be the most cost-effective among x431 series. This is why: https://launch-x431-v.blogspot.com/2017/03/why-need-new-l...

 

 

Launch M-Diag or Launch Easydiag?

 

 

Launch X431 Easydiag 2.0

Launch M-Diag Lite

Product

original-launch-easydiag

launch-m-diag-lite

Price

€59

 €85

Android

Apple IOS

Generic OBDII check

I/M check

Actuation test

 

4 systems diagnosis

 

(Engine, transmission, ABS, SRS)

FULL systems diagnosis

 

incl. bl-directional capabilities

IMMO & key programming

Oil / service reset

Brake pads

Battery matching

ABS bleeding

TPMS reset

Throttle body adaption

Steering angle reset

DPF regeneration

Injector coding

 

So, Launch M-diag Lite wins!  €85 not only covers X431 easydiag 2.0 and Golo easydiag+ (four+full systems diagnosis); but adds new special functions incl.Oil / Service reset, ABS bleeding, IMMO & key programming, throttle body adaptation, brake pads, steering angle reset, battery matching, DPF regeneration, Injector coding.

 

 

Launch X431 or Launch M-Diag or Launch Easydiag

 

For DIYers,

 

Launch M-Diag Lite OBDII code reader is much more powerful than Launch X431 Easydiag 2.0 and Golo Easydiag+. It not only excels in basic obdii diagnosis but special functions and actuation test

 

Launch M-Diag Lite details:

-Price: €84.95

-Language: English, Chinese, Spanish, French

-Car list: supports the generic OBD, CAN bus, and proprietary protocols of over70 car manufacturers and2, 500 car models

 

For garage repair work,

 

2017 Launch X431 V 8 inch pad is a good budget for reasons as below:

-Cheaper (€675) but more powerful than other launch x431

-Special functions available

-Full vehicle coverage: Brazilian, Indian, Chinese Australian, cars…

-2017 New vehicle support: BMW

-2017 New vehicle support: Toyota

-VW online programming without German server

 

05:38 Publié dans car diagnosis tool | Tags : launch | Lien permanent | Commentaires (0)