topblog Ivoire blogs

18/07/2016

Tango Key Programmer Update to V1.106 adds more free software

Tango Key Programmer Update to V1.106 adds more free software in obdexpress.co.uk,and free software listed below:

Tango V1.106 Update Software List (for Free):
[+] Techtream calculator: v9.30, v10.10
[+] Key maker Citroen Jumper 2012-(95640,HITAG)*
[+] Key maker Isuzu NPR 2007-(93C56,HITAG)
[+] Key maker Peugeot 206 2001- (95160,HITAG)
[+] Key maker Peugeot Partner 2002- (95160,HITAG)
[+] Image generator Chevrolet Spark (ID8E)
[+] Cloning of Toyota and Subaru 80 bit Keys**
[+] Added transponders CN2, CN5 to the Clone mode

How to distinguish the original and copy Tango Key Programmer?
Our Tango is original. For original device, there is the serial number. You can use this serial number to register your information on official website, then download the latest software to update your device online.

Update:This one is original. You need to update it when new software release.

Attention:After generating a new transponder with TANGO Programmer, you will not need any additional diagnostic equipment to program the generated transponder to the car! It will start the car directly, even on new FIAT CODE 2 system, also used in PSA Group vehicles! Only you have to write the new file back into the immobilizer system!

How to update Tango programmer to latest version:
1) Go to help option
2) Click online update

tango-key-programmer-with-basic-softwared-a-des-6.jpg
List of supported transponders:

Philips transponders:
PCF7930-31 writing, reading
PCF7935 writing, reading, shadow memory, crypto calculator
PCF7936 writing, reading, modes password, crypto, Manchester & Biphase encodings
PCF7941 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7942 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7943 transponder, remote, Manchester & Biphase encodings
PCF7944 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7945 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7946 transponder, remote, Manchester & Biphase encodings
PCF7947 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7952 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7961 transponder, remote, Manchester & Biphase encodings
*Auto switching between PCF7936-PCF7961 windows if invalid type detected.
*Autodetect manchester / biphase

Temic transponders:
Temic 11 reading , writing to T5
Temic 12 reading , writing to T5

Megamos transponders:
Megamos (13) reading , writing to T5 , emulating on PCF7930-35
Megamos (48) reading, writing, PIN, unlock by PIN, full range of memory contents, crypto calculation
Megamos CRYPTO-2 (8E) read ID, read/write EEPROM, write Cryptokey

Texas transponders:
Tiris (4C) reading
Tiris (4D) DST crypto reading, writing, crypto calculator
Tiris (4E) DST crypto reading, writing, crypto calculator
Tiris (8C) reading

Atmel:
TK5551M (T5 replacement)
SAAB reading , writing to T5
The product is in working out stages, therefore the list of the supported transponders will be developed later.

http://www.obdexpress.co.uk/wholesale/tango-key-programme...

05:39 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

16/07/2016

TOP 3 Mercedes MB CAN Filter at obd2express.co.uk [Statistics]

On basis of website statistics, the customer service makes a list of MB CAN Filters and offered the TOP 3 Mercedes CAN Filter here:

Rank Item No. Ordered items Price
1 SE103-B  MB CAN Filter 8 in 1 for W221 W204 W212 W166 and X166 W172 W218 W246 40.99
2 SE103 MB CAN Filter 3 in 1 for W222 W217 W205 (New Mercedes Benz S-series C-series) 36.99
3 SE129  MB CAN Filter 12 in 1 for W221 W204 W207 W212 W166 and X166 W218 W172 W246 W176 W117 W156 37.30

What is Mercedes CAN filter used for?
Mercedes CAN filter is designed for Mercedes-Benz W221 W204 W207 W212 W166 and X166 W218 W172 W246 W176 W117 W156 etc. models. These filters block old mileage data from EZS module. If you have installed filter on Mercedes-Benz vehicle in EZS module, then original dealer workshop scanner (like Mercedes Star Diagnosis Multiplexer or Xentry) will show same mileage in EZS as in vehicles instrument cluster. Also works for older vehicles like E-class W211, S-class W220, Sprinter. Mercedes-Benz filter can be installed also in instrument cluster, but in this case in EZS-EIS will stay old odometer mileage value.

Where to get MB CAN Filter wring diagram for Mercedes?

MB CAN Filter on Mercedes C-class W204
1- prepare Mercedes CAN filter board
check - resistor 121 must be soldered and solder second configuration points like in pictures

mb-can-filter-W204-1.jpg
2- Remove EZS board from casing.
Carefully disconnect board from mechanic – look on picture.

mb-can-filter-W204-2.jpg
3- Remove from EZS board SMD part marked with red “X”.
With short, good isolated wire connect Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5-5(GND), and 6-6 (+5V).

mb-can-filter-W204-3.jpg
4- After connection, insulate Mercedes CAN filter board with heat shrink or insulation tape. Put it carefully to EZS casing.

mb-can-filter-W204-4.jpg
Mercedes-Benz CAN Filter on Mercedes E-class W212
1- prepare Mercedes CAN filter board:
check - resistor 121 must be soldered and solder second configuration points like in pictures.

mb-can-filter-W212-1.jpg

mb-can-filter-W212-2.jpg
2- Remove EZS board from casing.
Carefully disconnect board from mechanic – look on picture.

mb-can-filter-W212-3.jpg
3- Remove from EZS board SMD part marked with red “X”.
With short, good isolated wire connect Mercedes CAN filter to EZS board according picture: 1-1 (C1H), 2-2(C1L), 3-3(C2H), 4-4(C2L), 5- 5(GND), and 6-6 (+5V).

mb-can-filter-W212-4.jpg
4- After connection, insulate Mercedes CAN filter board with heat shrink or insulation tape. Put it carefully to EZS casing.

Mercedes CAN filter wiring diagram reference:
http://obd2-diag.blogspot.com/2016/07/mb-can-filter-wring...

How to use MB CAN FILTER?

MB-CAN-Filter-8-in-1 (1).jpg

MB-CAN-Filter-8-in-1 (2).jpg

MB-CAN-Filter-8-in-1 (3).jpg

MB-CAN-Filter-8-in-1 (4).jpg

MB-CAN-Filter-8-in-1 (5).jpg

MB-CAN-Filter-8-in-1 (6).jpg
http://www.obdexpress.co.uk/wholesale/yh-mb-can-filter-18...

09:29 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

15/07/2016

FAQ about Super iCOM Software for BMW ICOM/ICOM A2

Super iCOM is one of the best after-market software for BMW diagnostic, coding, programming in the world, it is also an up-to-date software for online upgrade directly, software installed based on Windows® 8.1 64Bit OS, fit for most of the laptops/ PC in the market with SATA port.

Here is Frequent Asked Question about Super iCom Software

Q1: How many years of free updating can we enjoy?

Super iCOM provides one year free update online service.

Q2: How to upgrade my software via Internet?

You need use the Super iCOM Updater by inputting the serial number and password, after login you can choose the new version to download, the software will be updated and installed automatically.

User name: Serial number (The one find from Read SN icom on desktop)
Password: last 8 digits for password letter.

Attention: As software is large, please download the software one by one.

super-icom-bmw-icom-a2-software-hdd-des-1.jpg
Q3: What else shall I do before using this item?

Super iCOM software operation is very simple, just insert the SSD / HDD into laptop and power on, and connect the hardware to work with car directly, no need setting anything.

Q4: How can I renew the account if expired?

Account renew is also very simple, just contact with your local dealer, they will provide you the renew ID and password after your payment.

Q5: Software instruction:

INPA Software: Super ICOM has INPA software, but you need to use INPA firmware to work with your car, cannot use BMW ICOM firmware

super-icom-bmw-software-inpa-2.jpg
This software need setup. If you want to use INPA software, then setup to INPA software. If you want to use BMW ICOM software, then setup to icom software.

This is the setup software icon.

super-icom-bmw-software-inpa-3.jpg
If you use ICOM software, Choose STD:OBD first, then save, then enter the software. it is equal to switech the software.

super-icom-bmw-software-setup-4.jpg

super-icom-bmw-software-setup-5.jpg
When you use ISTA D, then switch back to ICOM.

http://www.mbstartool.com/service/mbstarshop-2016-black-f...

05:43 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)