topblog Ivoire blogs

26/10/2016

2015r3 TCS CDP PRO with BMW & Mercedes solutions

Here are some solutions of TCS CDP (cdp pro) running on BMW and Mercedes-Benz cars.

 

The reason that some CDP PRO cannot work with BMW or Mercedes-Benz:

The OKI chip is only for cars that support the PWM/VPWM protocol like Ford. BMW didn't use the PWM/VPWM protocol. The info that the TCS CDP does not work with BMW and Mercedes is bullshit.

 

The essential reason is located in problem with the m6636:

The problem with the m6636 is in the CDP pro not in cdp+. replace the 2 diodes and check if it works. the 2 diodes is for bmw and maybe mercedes, honda and others.

 

Solution of CDP PRO with BMW cars:

cdp-blue-back-side
the 2 diodes are D701 and D703. back the pcb. And replace it with 1n4148.  I have replaced these two diodes and gained the communication with BMW cars which users could not communicate with before. So, well DONE

 

Solution of TCS CDP with BMW cars:
You have to know that the components for TCS CDP interface, removed from old devices like tv´s, radio´s etc. check all solder Joints of all components (especially relays), so I have fixed the problem. I use the same interface for all BMW cars and it works without problems.

 

 

If solutions above doesn’t work also, spend a little money to buy a new TCS CDP unit tested ok.

tcs-cdp-pro-bluetooth-bmw-2 tcs-cdp-pro-bluetooth-bmw-3

This CDP PRO with 2015r3 software works without issues on BMW 3 series e90:

http://blog.obdexpress.co.uk/2016/06/24/2015r3-tcs-cdp-pr...

05:38 Publié dans Blog, Shopping, Web | Tags : tcs cdp | Lien permanent | Commentaires (0)

24/10/2016

Honda HIM HDS pcb rework for car connection problem

So I have one of those chinese HDS clones and Racy Jace was due to pop over yesterday afternoon, so I wanted to be sure I could get my Honda HDS HIM
connected to my Accord before Jace got there.

Unfortunately this didn't happen, no matter what I tried, the darn thing would not connect, now I have always had trouble getting it connected up and its just a pain in the back side. I failed to get the thing working in time for Jace visit to my place.

After Jace left, I thought I have another go, order of connecting things up seems very important with these things, so I went shopping for them.
He confirmed that I seem to be doing everything right, connected HDS to Com port of PC (make sure it's COM1), power on HIM (the actual box - Honda Interface Module), switch on ignition, start up HDS (Honda Diagnostic Software), click on connect, when it tells you to, plugin the OBD connector and voila it should work.

Nope still not connecting !! So I carry on messing about, try differing combos of powering it and connecting it without any joy. DD suggested that CJs theory is physical comm ports won't work and you need a particular type of USB-serial-COM port cable with specific Prolific USB drivers. Now I do actually have this cable and those drivers installed but had no clue where the USB serial cable would be.

With the combos exhausted and with me now getting annoyed I thought I try something different, on the HDS software there is a Self Test mode but to do this self test you need the loop back dongle plugged into the end of the OBD connector, and the chances of finding that somewhere were slim. Another option was to update the firmware on the HIM. So I thought lets try that, so I try it and it asks to press the button on the HDS for a few second, I press the button and hey presto it starts updating the HIM firmware.

Great, so its not got any issues with com ports, that part is working just fine. It then came flooding back to me, last time I used my HIM I remember suspecting that there was either a break in the OBD wire that comes out of the HIM or a connection/circuit issue on my HIM that was causing it not to be able to talk to the car.

So this time I decided to take it apart and have a look inside, this is what I was immediately greeted with :-

These are the solder pins for the OBD wire

honda-him-hds-fix-solution-1

These are the pins of the connector that connects the top and bottom boards together

honda-him-hds-fix-solution-2
Now both sets of solder joints were looking in a right sorry state, mostly rather dull looking, these could be referred to as dud solder or cold solder joint, which could result in giving bad electrical connection.

So what they needed was to be reflowed but there were a lot of them and do properly them one at a time would a real ball ache.
So what I did was take my gas soldering iron, remove the solder tip and use it with a naked flame and just heat up all the joints.

Here's the result :-

 

honda-him-hds-fix-solution-3

honda-him-hds-fix-solution-4
Actually those pictures aren't that great but the end result was that all the solder joints looked much much better, they all now had a shiny look to them rather than a dull look.

http://blog.obdexpress.co.uk/2016/10/24/honda-him-hds-not...

 

21/10/2016

Clone MPPS tools software download

This clone MPPS tools are a 1:1 of the original. Here download the crack mpps software v21 v18 v16 v13 with buying cables together.

 

MPPS software download:

MPPS V18 download

MPPS V16 clone

MPPS V13 software

 

MPPS V21 software update info:

 

OBD:

- Volvo ME7 CAN R/W/Cks:
Bench only at the moment.

- Volvo EDC15C11 CAN R/W/Cks:
Bench only at the moment.

- Bentley ME7.1.1 CAN R/W/Cks:
Master/Slave ECUs.

- VAG ALL TDI Bosch EDC17 X UDS drive now supports EDC17C46 and EDC17C64 ECUs:
Must be unlocked first using an MPPS container file.

- Generic Tricore VAG Only Multi ECU – MPPS Container file flasher:
Can be used to flash firmware updates and OBD UNLOCK files created using new VAS FRF file utility in tricore boot plugin.

 

Tricore Boot

- Added new file checksum utility for tricore, now supports:

(M)EDC Flash checksum

(M)EDC Eeprom checksum

Simos PCR

Simos 8

Simos SID305

- Added new VAS FRF file special function utility in tricore boot:

Create MPPS container file from FRF file.
Can be used to perform software updates using new protocol in MPPS.

Create OBD UNLOCK MPPS container file from FRF file.
Can be used to perform OBD unlock using new protocol in MPPS, currently supports Bosch EDC17C46 and EDC17C64.

Create READ UNLOCK MPPS container file from FRF file.
Can be used to perform full read unlock using new protocol in MPPS, currently supports Simos PCR. More options will be added for this ECU in future releases!

Create BIN file from FRF file.
Can be used when ECU can not be read from OBD.

 

Corrected various database and protocols errors.

 

This will be the last update for tools with serial numbers 41xxxxxx and 42xxxxxx and some of the new functions on this update will not be available for old hardware users.

The next release will support only newer hardware from serial numbers 43xxxxxx >
Users of older tools will be able to upgrade, details will be released before the next major update..

 

 

MPPS V18 release note:

 

Added Jaguar SID 204 R/W/C

Added Range Rover Sport SID 201/203/204 R/W/C

Added Jeep Patriot EDC16U31 R/W/C

Added VAG EDC17C46 OBD R/W/C (Only unlocked ECU’s)

Added Fiat ME7.6.3 W/C (Read can be done with the Multiboot plugin)

 

Updated Peugeot MED17 Checksum

Updated Fiat ME7.9.10 (Full or Data Write)

Updated Fiat MM8 Checksum

Updated Smart EDC16C31/32

Updated Ford EDC16C34

Updated some boot mode protocols (Will now write only what is different)

Updated VAG ME7 (You can now select the Memory)

On protocols with both CAN and KLine you can now select which you want to use.

http://blog.obd2express.co.uk/2016/10/21/mpps-software-do...