topblog Ivoire blogs

22/12/2016

Galletto 1260 user guide

Here in this blog, i will show you how to read/ write Peugeot 306 HDI ECU with cheap ECU Tuning Tool Galletto 1260 cable.
Carry out this procedure at your own risk.
 
The main contents include 3 parts:
Part 1: Setting up the galletto 1260
Part 2: Reading the ECU
Part 3: Flashing the ECU
 
Car model: Peugeot 306 HDI
ECU Typr: Bosch EDC 15 C2 29f400BT
 
  1. How to set up the Galletto 1260 tool?The best place to buy the Galletto 1260 ECU Chip tuning tool is OBDexpress. This costs
    €13.5
To use Galletto 1260, you need a stable laptop computer with a fully charged battery. For best results windows XP can be used.
When you receive the tool you must first copy the contents of the disc(will package with the unit) onto your desktop. Next connect the USB cable to the laptop and allow Windows to automatically install the correct driver. The driver used will be an FTDI driver. If it does not install automatically you may have to go in to: Control panel> Performance and maintenance> System > Hardware> Device manager. In this menu you will be able to select the tool and update the driver.
2. How to read the ECU by Galletto 1260?If possible run an extension cable down to your car and connect your charger. Make sure there are no other programs running that could cause the computer to crash.
At first you should Remove the fuse box cover which is beneath the steering wheel. To do this you must turn the clip a quarter turn. Perhaps Need A large flat blade screw driver  to do the job instead you.
– then Connect the Galletto inferface to the car’s diagnostics port and Connect the USB side to the laptop.
-Open the program named ‘NEW_SERIAL’.
-Switch on the ignition key to two clicks (don’t start the engine) until the test lights illuminate
-NEXT Select Peugeot/Citroen, Bosch EDC 15 C2 29f400BT.
-Select ECU data. You will then see a code such as 0281010362. This means that the tool has connected to the ECU successfully.
-Now select read data. You can name and save the ECU data. The file format should be **.bin (e.g. Peugrot-edc-15.bin)
-When reading is complete wait for the message and follow the instructions: Switch off the ignition and then click ok -> Wait ten seconds -> switch on the ignition and click ok.
-Now You should have a copy of your original ECU data file on your laptop.
-This file can be sent over to remap.
3. How to flash the ECU by Galletto 1260 interface?You have to transfer remapped file over tolaptop once you received it. And It is very important for you to check the file size is 512KB, you must also check the consistency of the file using the check sum tool:
-Connect the Galletto inferface to the car’s diagnostics port and Connect the USB side to the laptop.
-Open the program named ‘NEW_SERIAL’.
-Switch on the ignition key to two clicks (don’t start the engine) until the test lights illuminate
-Select Peugeot/Citroen, Bosch EDC 15 C2 29f400BT.
-Select ECU data. You will then see a code such as 0281010362. This means that the tool has connected to the ECU successfully.
-Select ‘Open file’, and then select the new remapped file which you wish to load to the ECU.
-Select download file. This step can not be interrupted, so Make sure there is no other software running and don’t knock the cable etc, it’s best to remain completely still to eliminate any possible risk.
-Afterwards, when the program prompts, switch off the ignition once the lift pump has stopped. Then press ok and wait ten seconds. You will then be prompted to switch it back on. Do as instructed and the process is complete.
Now You can enjoy your remapped ECU!

http://ktagecu.blogspot.com/2016/12/how-does-galletto-126...

21/12/2016

Buy Renault CAN CLIP clone China know the reason

Has anyone bought a renault can clip diagnostic interface? How much it should be ok? Check Best-quality Renault CAN CLIP china and the Cheapest CAN CLIP clone. And it talks.
 
How to ensure your Renault CAN CLIP diagnostic interface is the BEST-QUALITY?
Best-quality Renault CAN CLIP
Best-quality Renault CAN CLIP  pcd
 
 renault-can-clip-an2135sc-chip
This is Quality A+++ Can Clip for Renault with the high quality chip CYPRESS AN2135SC or CYPRESS AN2136SC.
The new chip AN2135SC/AN2136SC solved communication issues of other CLIP versions. That make CLIP work more stable and can be used for a longer time
 
Using other versions of Renault CLIP, the diagnostic interface will disconnect if users have no operation for 10 minutes around after successful communication to the car.
 
With this new CAN CLIP for Renault, the issue solved, with the chip AN2135SC/AN2136SC. This is the PCB with new design.
new CAN CLIP for Renault pcd

 

new CAN CLIP for Renault pcd
sp19-a-renault-can-clip-pcb-1 sp19-a-renault-can-clip-pcb-2
So that it can works no issues as the original. That is, it’s the BEST-QUALITY Renault CLIP china clone.
 
 
Where to buy the CHEAPEST Renault CLIP china clone?
This is the source with the cheapest clip:http://www.obdexpress.co.uk/wholesale/can-clip-diagnostic...
sp19-d-cheapest-can-clip
sp19-d-can-clip-v162-pcb
 
This is the NEWEST Renault Clip china clone, just released on Dec. 2016. It is only for $105, the CHEAPEST version, compared to others. Work no issues of the basic obdii functions.
 
 
So, Renault can clip china clones only differs in PCBs and price. All have been tested without issues on Automatic test of all computers, Physical measurements, OBD diagnostic tests, Airbag test, Antipollution, Multimeter inEnglish/ German/ Brazil/ Denish/ Spanish/ Finnish/ French/ Italian/ Norwegian/ Dutch/ Portuguese/ Romania/Swedish.
 
Tip 1: Quality & Price
In China, you can get anything – at/for any price, problem is that you will have to accept the quality. “You get what you pay for” – And this is more or less true, there will be always someone somewhere “trying to” do it for less, but there are thresholds and once you step under them, you will have to suffer from the results. Quality of a product also depends on the material you purchase (You can’t simply make gold out of wood)
 
Tip 2: Reasons for low costs
The only reason why the obdii diagnostic cables are made in China is because 90% of the materials (micro-controllers and ICs) come from there. That is, it’s mainly about cost, most people would not be ready to pay 3-4 times the price just for the device being made in Europe or the US.
So, items are produced in high quantity and cost saving here
 
Anyway, good luck and enjoy clipping.
 

20/12/2016

Digiprog 3 OBD change mileages for 2011 nissan micra 1.5 93c66 eeprom

There has two options for you how to change mileage on 2011 nissan micra,first one to change KM via OBDII using odometer correction tool-digiprog 3 DP3,another is change mileages with removal of the dashboard.
Enjoy!
-> change km via OBDII using Digiprog 3 clone
2011 nissan micra 1.5 tekna 93c66 eeprom use honda accord c66 option on Digiprog same algo by desoldering and using clip st01 to read and write, no need to remove needles chip on back of board
 

 

 
-> change mileages with removal of the dashboard
  1. Remove the dashboard and open it carefully.
 
NISSAN-MICRA-2011-93C66-dash
  1. Locate the 93c66 EEPROM memory.
  2. Find correct position of PIN1.
 
Connect-cable-C4-to-EEPROM
  1. Connect the EEPROM memory using C4 cable.
NISSAN-MICRA-2011-c4-cable
 
  1. Make sure that you connected the C4 clip correctly.
  2. Press the READ EEP button and save EEPROM memory backup data.
  3. Press the READ KM button and check if the value shown on the screen is correct.
  4. CHANGE KM.