topblog Ivoire blogs

27/09/2018

How to use TIS2000 for Saab (TIS2008-2) for Tech 2

For anyone happy using TIS2000 for Saab (TIS2008-2) follow these steps:

First, get your hands on a Tech 2 handset, CANDI and cables etc. Make sure you are confident that your serial connections are good.

1. You will need a TIS2000 USB key and patch for activation (can be bought for little money or sourced elsewhere)

2. Download and install TIS2000 for GM/NAO. You may be prompted to install the USB key – just follow the steps. When finished, don’t run the TIS2000 program.

3. Download Saab TIS2008-2. Insert into same physical/virtual CD drive you installed the TIS2000 GM from (drive letter needs to be the same).

4. Launch TIS2000 from desktop icon/start menu

5. TIS2000 should detect available update (Saab TIS-2008). OK this and let it run.

6. If you haven’t installed the USB key and patch do this now.

7. Launch TIS2000 and click on SPS or security access to ensure it works

8. Enjoy!

I believe this will allow re-programming of models up to 2008 only, so if you have a later model, you’ll probably need GlobalTIS.

If you’ve bought a clone Tech 2 unit I’d recommend throwing away the supplied flat RJ45/ethernet cable and replacing it with a standard ethernet cable (not cross-over) as mine was faulty and caused many headaches! The correct pin-out is provided by the RJ45 to D9 adaptor. For those interested, only pins 4 and 5 on the RJ45 socket are used (TX/RX).

 

IMPORTANT:

You may well have a couple of issues getting the software running initially. If your web browser refuses to connect to the TIS2Web service, it’s likely that one of the two GlobalTIS services are not running. To fix this, open the ‘services’ console either by

Start>Run and type “services.msc”

OR

Right-click ‘My Computer” select ‘Manage’ and drill down to the services icon on the left pane.

There are two services that should be running and they’ve got obvious names, something like GlobalTIS and TC6 (not near my TIS PC at the moment) and sit next to each other in the services list. In the information pane they should say ‘started’. If not, right-click and select ‘start’. If this fails with an error, try modifying the registry key below.

To open registry editor Start>Run regedit BE CAREFUL MODIFYING THE REGISTRY – YOU CAN REALLY SCREW YOUR PC UP!!!!!

In the left pane, expand the keys until you find the following

HKLMSoftwareApache Software FoundationProcrun2.0Global TISTC6ParametersJavaJvmMx

Change the value of this key from 0X0000044 to 0X00000200 and exit the registry. Try to restart the service – you should find it now works. Don’t ask me why, I got this fix from another forum – fair play to the guy who found it.

Hope this helps someone!

14/09/2018

The BEST Solution for Newbies Failed to Install/Activate Xentry XDOS

This is the best solution for newbies who has trouble in 09.2018 Xentry XDOS installation or activation:

http://www.obdexpress.co.uk/wholesale/mb-sd-connect-compa...

 

Why do I think it’s the best for newbies?

Because the full kit (SDconnect C4 + 09.2018 XDOS + Dell D630)  is handy and help save a lot.

XENTRY-DAS-OPENSHELL-1

 

All software is installed on the Dell D630 laptop, done before shipping to your end.

With the dedicated serial port on D630, there is no issue for users…. it was plug and play… the HDD with Mercedes software is loaded into the Dell laptop and WIS/EPC and XENTRY/DAS has been activated with “activation keys” before delivery...you can use it for Mercedes-Benz diagnostics, coding or programming with SD connect C4, when you receive the package.

   

 

 

 

 

Source: http://www.obdexpress.co.uk/wholesale/2018-09-mb-sd-benz-...

 

Note that HTT-WIN is updated to 09.2018 Mercedes software disk. Software released in 2017 and 2018 doesn’t come with HTT-WIN. But now, it comes again!

09.2018-htt-win-mercedes

 

On a side note, Dell D630 is second-hand but 100% functional - no worries!

 

 

With the SD connect C4 full kit, you’ll NEVER have issues of setup on a laptop, installation and activation as what the users complaints

 

Attach: Error and solution on Dell D630

 

Error: have now installed it on my recently acquired Dell 630. Everything installed well, however when I get to the point of using it and it automatically goes to use HHT(as my car is a 1993 model)it says"diagnostic connector is being initialised" however then it says"com port assigned! close other use!"

Solution: go to the windows system menu in control panel and under the harware section look at the com port assignmennts and make sure the com port you designated isn't already assigned to something else.

 

also, does the dell630 have a dedicated RS232 com port or are you using a usb/pcmcia/cardbus to RS232 converter.

 

This is the best solution for newbies who has trouble in 09.2018 Xentry XDOS installation or activation:

http://www.obdexpress.co.uk/wholesale/mb-sd-connect-compa...

 

Why do I think it’s the best for newbies?

Because the full kit (SDconnect C4 + 09.2018 XDOS + Dell D630) is handy and help save a lot.

All software is installed on the Dell D630 laptop, done before shipping to your end.

With the dedicated serial port on D630, there is no issue for users…. it was plug and play… the HDD with Mercedes software is loaded into the Dell laptop and WIS/EPC and XENTRY/DAS has been activated with “activation keys” before delivery...you can use it for Mercedes-Benz diagnostics, coding or programming with SD connect C4, when you receive the package.

 

Source: http://www.obdexpress.co.uk/wholesale/2018-09-mb-sd-benz-...

 

Note that HTT-WIN is updated to 09.2018 Mercedes software disk. Software released in 2017 and 2018 doesn’t come with HTT-WIN. But now, it comes again!

On a side note, Dell D630 is second-hand but 100% functional - no worries!

 

 

With the SDconnect C4 full kit, you’ll NEVER have issues of setup on a laptop, installation and activation as what the users complaints

Xentry-XDOS-installation-actvation-best-solution-1

 

Xentry-XDOS-installation-actvation-best-solution-2

 

Attach: Error and solution on Dell D630

 

Error: have now installed it on my recently acquired Dell 630. Everything installed well, however when I get to the point of using it and it automatically goes to use HHT(as my car is a 1993 model)it says"diagnostic connector is being initialised" however then it says"com port assigned! close other use!"

Solution: go to the windows system menu in control panel and under the harware section look at the com port assignmennts and make sure the com port you designated isn't already assigned to something else.

 

also, does the dell630 have a dedicated RS232 com port or are you using a usb/pcmcia/cardbus to RS232 converter.

 

 Source:http://blog.obdexpress.co.uk/2018/09/14/xentry-xdos-insta...

13/09/2018

FGTech Galleto Driver Windows 10: How to Install + Review

Here are FGTech Galletto Windows 10 installation tips and guides, including how to solve FGTech error “driver is not digitally signed”

 

It’s possible that the PC cannot recognize the device, after you have installed Setup.exe in Windows 8 and made it connected by the USB cable.

The reason can be: the driver is not installed

If you try to install the driver manually through the peripheral management it will display the following error message: This driver is not digitally signed

 

 

It’s possible to solve the program in Windows 7 operation system

 

Even if it does not accept the driver manually, you can disable the control if the driver signing

Here you go...

 

Reboot the PC in an advanced mode

On Desktop, open the Charm Bar to the right can click on Change PC Settings

 

Now. Click on General - Restart now

 

PC will restart in an advanced mode

On windows 10, it will appear the following interface

Click on Troubleshoot - Advanced options - Startup Settings - Restart

 

 

 

 

PC restarts, then go to Startup settings

Disable driver signature enforcement

 

PC will restart

Then you can install the FGTech driver

 

Galletto V54 Windows 10 64 bit Review:

i have probation galletto on windows 10 64 bits and work s good.

soft is from fantomel post "rework and up loads v54 to v53 0475 fw."

mostly problems with software no open is pc or laptop

trying on sony vaio netbook no work

Acer aspire 5920 ati video no work

HP Compaq 610 nvidia work good

Acer Aspire 6930 nvidia work good

read fantomel post download software install C/Fgth .

plug galletto usb install driver from software C/Program files/Fgth/drivers.

many problems is pc with amd procesors and ati video card NO WORK

 

Have fun

http://simefuneralforum.com/blogs/obdiiexpress/