topblog Ivoire blogs


VVDI2 Key Programmer Customer test result and feedbacks

VVDI2 feedback:
I successfully added a key bcm2 on a 2013 audi a5.
2007 Audi A4 B7 RB8 crypto – mileage correction ok
Audi BCM2 add spare key by obd worked fine, and I did one on a 2013 A5 and it worked flawlessly.
A6/Q7 EZS Kessy: Added a dealer key (remote sourced from the dealer) without issues. Seemed to read everything properly but I had a working key to begin with.

Audi A6: Testet with A6 read kessy working, learned new key
Skoda Octavia 2006: got CS & PIN , programmed key fine, but not remote programming.
VW passat. B5: Pulled PIN, programmed key, corrected miles.
VW Passat B6 2009: Pulled PIN but couldn’t get 6 bytes CS, needed comfort dump.
VW Transporter T5 2006 : Pulled PIN Programmed key, no remote programming.
Audi A4 2006 : mileage correction success .
Audi A6 2003: Mileage correction fail. car not start. remove battery terminal. car start.

Customer test result
-Transfer instrument cluster in 2010 A5 + Mileage change ..YES GOOD
-Make OEM key for 2006 Audi A6 ... YES GOOD
-Change mileage in 2006 Audi A6 ... YES GOOD
-READ Kessy EZS OBD Audi A6 2006 ...YES GOOD
-READ BCM2 (BDM) 2010 Audi A4 ... YES GOOD
-All functions on older cars year 2000-2004 era working well ...YES GOOD

08:30 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

XPROG-M Programmer 5.5.5 Read EEPROM FLASH of Audi A6 2005

Sharing!! pin out MCU with XPROG-M programmer, to read/write EEPROM and flash memory of 2005 Audi A6.

Device i used:
Lenovo T420
XPROG-M ECU programmer v5.55

Audi A6 Steering Lock 2005 with OEM 4F0905852B
MCU= 3L40K secured
read by XPROG-M
use adapter 1-002-0017
Eeprom + Flash

XPROG-M Programmer-1.jpg
I have done 4pc of this unit last month.
Short cables max 12cm long.
When it don’t read always try to lift reset pin
(I have never done it but some Xprog is sensitive and then try lift reset)
Operate by following my instruction, one friend used the adapter (BDM) and wires with a length of 10 cm. RESET leg lift.

XPROG-M Programmer-2.jpg
(the program automatically detect MC9S12 device type, flash memory size abd bypass MCU security.
Motorola HC(S)12-secured

MCU is dead! Work 100%

XPROG-M Programmer-3.jpg

XPROG-M Programmer-4.jpg

XPROG-M Programmer-5.jpg

XPROG-M Programmer-6.jpg

XPROG-M Programmer-7.jpg

06:45 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


PIWIS Tester 2 Development/ Engineer Mode, what can do?

With piwis tester 2 clone or original AllScanner VCX-Plus mux, three modes exists but only two modes can be available-- E (engineer/development) mode with German, V (aftersales) mode with multi-language. Details of PIWIS Tester 2 V16.2 Engineer/Development Mode is offered.

Tester 2-Engineer-Mode.jpg
Tools for Engineer Mode:
Piwis Tester II scanner
AllScanner VCX-PLUS Multi Scanner

What can Engineer Mode do?
1.start/stop”LAST MODE”wait for stopping the engine and change memory
2.spoiler”lessen time when the car starts
4.spoiler”change angle”
5.Change VO code
6.Close Air Mercury
7.Upgrade power
8.Remove the tire pressure sensor
9.Install reversing camera
10.Install USB/BT
11.Close the seat belt warning
12.Change CDR/PCM operation interface
13.Air condition memorization
14.Start CDR_AUX
15.Open the PCM function
16.Manually set codes
17.Automatically set codes
18.Manually do programming
19.Automatically do programming

Tester 2 V16.2 Engineer Mode display:

Tester 2-Engineer-Mode (1).jpg

Tester 2-Engineer-Mode (2).jpg

Tester 2-Engineer-Mode (3).jpg

07:05 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)