topblog Ivoire blogs


MPPS V13.02 software installation problem and solution

One of our customer install the software of MPPS and meet the following problem:

Problem is that you do not install the driver well. For mpps software, you need to install the driver. Please install the driver on installation contect.

Free download MPPS V13.02 driver software here:

MPPS V13.02 Chip Tuning Demo Video:

MPPS V13.02 software driver installation on Win 7

07:50 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


Latest V16.2 Porsche Piwis Tester II with CF-30 Laptop support WIFI

V16.2 Piwis Tester II WIFI Version Diagnostic Tool for Porsche with CF-30 Laptop

V16.2 Piwis Tester II price:€1191.74+shipping

V16.2 WIFI Version Piwis Tester II Highlights:
1. Latest tester for Porsche
2. Powerful functions
3. Full access to Porsche
4. Update procedure: Buy new Hard Disk
5. Software Version: 16.2
6. Support WIFI
7.Language availability: German, British English, American English, French, Italian, Spanish, Japanese, Chinese, Russian, Portuguese, and Dutch.
8.After Sales Service:
a.One year free maintenance
b.One year free update
c.Long-term technical support

Hardware Information:

Porsche Piwis Tester II Support Systems:
ENGINE automatio transmission, air-conditioner, SRS, ABS, ASR, MPL, GM, Original antitheft System, KEYLESS GO system, OBDII system.

Porsche Piwis Tester II Vehicle Coverage:
1. 911(997) (991)
2. Boxster/Cayman (987)
3. Cayenne up to MY 2010
4. Cayenne from MY 2011
5. Panamera



More information:

08:09 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)


How to solve Kess V2 Bootloader adapter problems

Find a solution to fix Kess v2 clone bootloader adapter problems. Just put it here for sharing.


Kess v2 with ksuite 4.036 (China clone)


I am having problems with my bootloader adapter for Kess v2. Kess is reworked to 4.036 and works with OBD cable. I tried to use bootloader adapter and cable, but failed to read any ecu. I tried to connect EDC17CP14 (on the bench and without boot pin- obd mode on the bench), no luck with Kess (but my reworked Galletto worked with similar wiring ID + read OK).

I already checked the wiring in the cable connector- fixed some wires, but still nothing.

I think there may be something wrong in the bootloader unit.

4 steps to solve bootloader adapter problems:

Step 1- fixed the wiring

i fixed the wiring in the connector that goes into the bootloader module like in the picture (Ktag has the same) 4 wires were wrong in my connector.

Step 2- resoldered the mosfet

And I resoldered the mosfet (in the middle of the module- near the middle LED).

Step 3- read ECU without opening

I then got the power to the ecu. But it didnt read it, probably because I didn’t connect the boot pin (that needs to be soldered on the ecu pcb). I tried to read it without opening, because I borrowed the ecu.


Step 4- opened the ECU to read

So I finally got the time to test my bootloader module with all wiring (boot cable attached). Once I opened the ECU (edc17cp14) and connected the boot pin, I was able to succesfully Id and read the ECU.

Worked like a charm!

The main problem was the soldering of the mosfet transistor in the middle of bootloader pcb, and I remowed the extra wire that was on the other side of the pcb.

Hope this helps those with Kess V2 unit from China

(NOTE: This is a cutomer solution; please try and responsible for what you will do)

03:13 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)