topblog Ivoire blogs

17/09/2018

How to use Condor Mini + Tibbe Jaw M3 cut Jaguar 8 cut key

How-to's:How to use Condor Mini + Tibbe Jaw M3 cut Jaguar 8 cut key 

 

It’s aimed to cut a Jaguar 8 cut key with a Condor Mini machine

 

Have just cut the key and it seems to be 1 cut in front / 1 cut behind in placement.

 

 

 

 

 

 

Q: How far should this screw be in / how far out should it be??

 

A: tbe1

 

 

 

 

 

Q: How much does the rear screw need to stick out?

 

A: It is necessary to re-adjust the position of the key in the vice.

 

 

 

Q: what the best way to make sure it lines up in the correct place perfectly.

 

A: With the correct attitude, the machine itself will go to the right distance to puncture the key into the position of the first secret. at Ford it is shorter.

 

 

 

Q: I will give it another go fingers crossed lol

 

A: if properly configured for the Ford device, then do not re-adjust the vise of the length of the bolt. stand the workpiece of the key and cut it

 

 

 

 

 

Q: how far out do you have your screw?

 

A: in the vice, the key is the Ford, and the milling cutter has entered the required length independently. Do not be afraid

 

 

 

Q: the last cut i did was wrong it was to far forward by nearly a complete cut

 

 

 

A: It is necessary to adjust when the milling cutter stands in such position as at me on a photo. remove the vice and adjust the depth of the key with the screw, each time looking closely at how the milling cutter is positioned. The cutter must be in the position of the first secret

 

you do not have a vise

 

as you adjust the screw, tighten the fixing nut so that the screw does not hang and unwind. I'm sorry, I've got to go to the client.

 

try to insert the key deeper. with effort.

 

Source:http://blog.obdexpress.co.uk/2018/09/17/condor-mini-tibbe...

 

04:36 Publié dans car key programmer | Tags : xhorse | Lien permanent | Commentaires (0)

14/09/2018

The BEST Solution for Newbies Failed to Install/Activate Xentry XDOS

This is the best solution for newbies who has trouble in 09.2018 Xentry XDOS installation or activation:

http://www.obdexpress.co.uk/wholesale/mb-sd-connect-compa...

 

Why do I think it’s the best for newbies?

Because the full kit (SDconnect C4 + 09.2018 XDOS + Dell D630)  is handy and help save a lot.

XENTRY-DAS-OPENSHELL-1

 

All software is installed on the Dell D630 laptop, done before shipping to your end.

With the dedicated serial port on D630, there is no issue for users…. it was plug and play… the HDD with Mercedes software is loaded into the Dell laptop and WIS/EPC and XENTRY/DAS has been activated with “activation keys” before delivery...you can use it for Mercedes-Benz diagnostics, coding or programming with SD connect C4, when you receive the package.

   

 

 

 

 

Source: http://www.obdexpress.co.uk/wholesale/2018-09-mb-sd-benz-...

 

Note that HTT-WIN is updated to 09.2018 Mercedes software disk. Software released in 2017 and 2018 doesn’t come with HTT-WIN. But now, it comes again!

09.2018-htt-win-mercedes

 

On a side note, Dell D630 is second-hand but 100% functional - no worries!

 

 

With the SD connect C4 full kit, you’ll NEVER have issues of setup on a laptop, installation and activation as what the users complaints

 

Attach: Error and solution on Dell D630

 

Error: have now installed it on my recently acquired Dell 630. Everything installed well, however when I get to the point of using it and it automatically goes to use HHT(as my car is a 1993 model)it says"diagnostic connector is being initialised" however then it says"com port assigned! close other use!"

Solution: go to the windows system menu in control panel and under the harware section look at the com port assignmennts and make sure the com port you designated isn't already assigned to something else.

 

also, does the dell630 have a dedicated RS232 com port or are you using a usb/pcmcia/cardbus to RS232 converter.

 

This is the best solution for newbies who has trouble in 09.2018 Xentry XDOS installation or activation:

http://www.obdexpress.co.uk/wholesale/mb-sd-connect-compa...

 

Why do I think it’s the best for newbies?

Because the full kit (SDconnect C4 + 09.2018 XDOS + Dell D630) is handy and help save a lot.

All software is installed on the Dell D630 laptop, done before shipping to your end.

With the dedicated serial port on D630, there is no issue for users…. it was plug and play… the HDD with Mercedes software is loaded into the Dell laptop and WIS/EPC and XENTRY/DAS has been activated with “activation keys” before delivery...you can use it for Mercedes-Benz diagnostics, coding or programming with SD connect C4, when you receive the package.

 

Source: http://www.obdexpress.co.uk/wholesale/2018-09-mb-sd-benz-...

 

Note that HTT-WIN is updated to 09.2018 Mercedes software disk. Software released in 2017 and 2018 doesn’t come with HTT-WIN. But now, it comes again!

On a side note, Dell D630 is second-hand but 100% functional - no worries!

 

 

With the SDconnect C4 full kit, you’ll NEVER have issues of setup on a laptop, installation and activation as what the users complaints

Xentry-XDOS-installation-actvation-best-solution-1

 

Xentry-XDOS-installation-actvation-best-solution-2

 

Attach: Error and solution on Dell D630

 

Error: have now installed it on my recently acquired Dell 630. Everything installed well, however when I get to the point of using it and it automatically goes to use HHT(as my car is a 1993 model)it says"diagnostic connector is being initialised" however then it says"com port assigned! close other use!"

Solution: go to the windows system menu in control panel and under the harware section look at the com port assignmennts and make sure the com port you designated isn't already assigned to something else.

 

also, does the dell630 have a dedicated RS232 com port or are you using a usb/pcmcia/cardbus to RS232 converter.

 

 Source:http://blog.obdexpress.co.uk/2018/09/14/xentry-xdos-insta...

How to fix Mart Tool error "file link unavailable"

If your Mart tool key programmer has error "file link unavailable",how to do?

mart-tool-file-link-unavailable.jpg

 

Here Mart tool Land Rover & Jaguar key programmer:

 

 

 

Solution:

Free download this file

https://mega.nz/#!oQhgkABZ!712ziCtJEnmb4lJIyC_u-17-R1lGuU...

Size:1.6MB

Provider: www.obd2eshop.com engineer

Note: Uninstall the anti-virus software.

 Source:

 

http://blog.obd2eshop.com/solved-mart-tool-error-file-lin...