topblog Ivoire blogs

31/10/2019

How to solvec STIC FVDI J2534 IDS Software Vehicle Communications Error

STIC FVDI J2534 Ford Mazda got an error "An active IDS software license is not found on your computer and is required to establish communications with the vehicle".

stic-fvdi-j2534-an-active-ids-software-license-not-found

 

obdexpress.co.uk engineer solution:

Please install Ford IDS software in one computer and install Mazda IDS software in another computer.

  1. visit: www.flyobd.com
  2. Click on "Download".

 

-> For Ford diagnostic & programming software, Please download and install:

1) SVCI-J2534-Ford V1.1.5.1 

https://mega.nz/#!6zQTgAaJ!-J6Bz7G9_P2N1IyjDeqLmFSPboAwwI...

2) IDSFord V115.01                                    

3) IDS_VCI V1.03

https://mega.nz/#!anBG3CZa!SyersJzW3BA_FLFuBBK-hFU2JwGNvu...

 

->For Mazda Ford diagnostic & programming software, Please download and install:

1) SVCI-J2534-Mazda V1.1.5.1

2) IDSMazda v115

 

Good luck.

More question, please contact at Sales@OBDexpress.co.uk

 

Or you are looking for Ford IDS V115 version, here you can go STIC FVDI J2534:

http://www.obdexpress.co.uk/wholesale/fly-fvdi-j2534-mazd...

 

10:31 Publié dans software download | Tags : ford ids | Lien permanent | Commentaires (0)

30/10/2019

How to use IDS to solve Ford Edge 2008 not starting, no spark

Ford Edge 2008 will not start, there is no spark

When I turn on the ignition, fuel pump shakes once, you turn the starter turns but the RPM do not rise,

Scanner also showing that there is no symptoms of crankshaft signals,

But other parameters of other sensors Like engine coolant, air temperature , the gas pedal, electronic throttle control, mass air flow sensor is OK

Wiring from crankshaft sensor to PCM is OK.

Resistance of crankshaft sensor is also OK. its about 700 Ohms

(Immo related fault or Other Computer faults does not have, )

Interesting thing is this when you disconnect any other sensor or injectors, PCM is detecting disconnected sensors
but it’s not detecting that crankshaft sensor fault. even after cranking it’s not showing, cranshaft missing fault is not appearing on faults list .

 

What to do:

Program another known good PCM if problem persists check continuity of CKP harness and probably replace CKP sensor.

 

When you replaced with a used PCM it’s not compulsory to change VIN. Just make sure the programming procedure is properly followed.

 

Finally.

pins from sensor to ecu contacts once again checked, checked crankshaft clearances, the car started.

 

The conclusion is the following: for diagnostics by OBD one can’t see any error, Autel Maxisys ( FORD) and Launch 431 ( FORD) also don’t see that there is a crankshaft sensor or not. maybe there is no such function at all in the PCM itself to sense disconnected crankshaft sensor … if it is a factory made then it should not repeat again … if not, then sooner or later this car will not start again ….

No any of above scanner are seeing RPM while starter turns, its showing RPM after the engine is running

Best bet is to use FORD IDS for PCM programming.

 

***NONE of the clone VCM2 will do old PCM programming is because of the EEprom programming signal higher voltage required can’t be produced by those clones.

In short, when programming these PCM, the VCM sends a higher voltage (around 18v) to 1 pin of the PCM to “open” the programming session. Clones can’t do that.

Better get an OEM VCM2 as I did.
Buy 1 good tool instead of 2 or 3 crap tool

 

How to use Ford IDS for PCM reprogramming?

Note: The following parts show how to use the best VCM2 Ford IDS (Item No. SP177) do the PCM programming. As for the other version of VCM2, please try at your own lucky.

 

Please connect the cloned VCM2 unit to the car and run Ford IDS

Step 1:Select the toolbox tab at the top of the screen

 

Step 2: Select “Module Programming

 

Step 3: Select the tick mark or the Enter key

 

Step 4: Select “Module Reprogramming

 

Step 5: From the fly out menu, select the type of module to be reprogrammed

 

Step 6: Select the tick mark or the Enter key

 

Step 7: The application will compare the current calibration level to the latest one available for that vehicle. A message will appear.

 

Step 7A: If no later calibration is available, a message will appear indicating this. Select the tick mark or the Enter key to return to the Module Programming menu.

 

Step 7B: If a later calibration is available, a message will appear asking if you want to reprogram the module with this calibration. If you do not want to reprogram the module, select “No”. You will be returned to the Module Programming menu.

 

Step 8: If you want to reprogram the module, select “Yes” in response to the question “Do you want to program the vehicle with this calibration?”

 

Step 9: Make sure that an Internet connection has been established and then select ”Confirm”

 

Step 10: You will be presented with a screen that recommends that you carry out Self Test. If you choose to complete this test, you will receive a list of Diagnostic Trouble Codes (DTC’s) that have been set on the vehicle. When finished viewing this list, select “Exit”.

 

Step 11: Follow the on-screen instructions to prepare the vehicle and turn the ignition key off and on.

Select the tick mark or the Enter key after each one.

 

Step 12: If necessary, apply the reprogramming label to the PCM

If an emissions recall has been performed or a required emissions-related TSB has been completed, an Authorized Modification label must be placed on the PCM. These labels can be purchased at the parts counter of a Ford or Lincoln/Mercury dealership.

 

Step 13: Select the tick mark or the Enter key to return to the Module Programming menu of Ford IDS.

 

29/10/2019

Autek IKey820 Reviews For Ford Key Programmer Via OBD

Put together all the good feedback of Autek IKey820 key programmer via OBD for Ford cars. IKey 820 does not have coil reader, only work with obd, so the operation is easy to follow the on-screen instruction.

Autek IKey820 is the best solution for all Ford cars from 2004 -2018 year, it is as cheap as €511GBP.

 

Autek IKey820 Ford car models:

http://www.obdexpress.co.uk/upload/pro/autek-ikey820-immo...

Ctrl+F to search Ford.

For newest update, visit: http://www.autektools.com

Like:

autek-ikey820-ford-update-1

Autek IKey820 tokensIKey 820 comes with 500 tokens. When you finish 500 tokens, you can reload another 200 tokens again and again.

 

IKey 820 Ford key programming feedback: SUCCES

AKL = all keys lost

 

2003 Ford Ranger AKL added one key at a time, no 10 minute.

2014 F150 added key

 

2008 Ford expedition all

Ikey820 selected by model/year

add key in 10 seconds success

 

2002 taurus add key

5 seconds SUCCESS

2005 ford excursion erase all and add keys work just fine

10 minute wait SUCCESS

 

Tried a 2018 Fusion add prox with paid update. Gave me pincode error on 5 min wait screen.

 

2010 ford f150 AKL

Used add key by model/year

Bypass and program in 5 seconds

2015 ford f150 USA add key 128 bit T key

Selected by model and year add key

It said wait 10 minutes

2 minutes later it said insert new key and turn on

2016 Ford fusion titanium USA prox AKL

After getting door code from back of smart junction box and turning off alarm

Select Ford fusion 2016 key and Keyless 1 with prox in slot in armrest

Said wait ten minutes

After maybe 3 minutes keys programmed doors cycled and programmer displayed key count +1

2000 Ford Excursion. Programmed after 10 mins. All good.

08 Chevy malibu AKL USA

12 minutes and programmed success

09 Nissan murano AKL USA

plugged in and programmed in about 20 seconds SUCCESS

 

Ford Mustang 1999

Parameter Reset for cluster change, 10 min wait, said okay. Delete stored keys and add back original key and 2nd key after maybe 8 mins. Started up.

OKAY

 

2010 Ford Fusion AKL

Programmed fine after 10 min wait. Even MVP has no bypass 10 min wait on this one.

OKAY

 

2004 Ford Explorer - Added a key in less than 5 seconds!

 

2010 f150 key added in 5 seconds

 

2016 ford mustang prox 900Mhz remote start AKL USA ACTIVE ALARM

i test on Ford f150 2009 for add key after aprox 10 seconds success, i think than bypass 10 minutes wait for access granted

 

I test on Ford f150 2017 with blade key work perfect.

 

16 Ford focus went under 12 escape 10 min wait success

2006 Ford Escape success bypass wait add key.

2006 Ford Explorer add key bypass wait

2007 f150. Less than a minute

2016 Ford Mustang done under a minute

2013 Ford Explorer Add Key Success 10 min wait, but I feel like it went faster.

2007 Ford F-150 program in about 12 minutes

 

2001 Ford expedition 10 min and done.

 

2001 Ford Mustang success 10 min wait akl. No add key so had to use ghost key to add .

2005 Ford Focus success 10 min wait akl.

 

2003 F150 no place to add a key erased their key and added two keys work perfectly 10 min wait

08 ford e-350 van Key type 2 7 seconds Impressive

04 ford explorer

16 Ford explorer prox

 

2014 FORD F-150-DUP REMOTE MASTER–10 MINUTE WAIT NO ISSUES

2011 f-150 add a key 10 min wait and done

2014 F150 Add key 10 minutes and done.

99 ford explorer, akl 10 min wait and done

14 escape keyed add Said wait several min Bing Bing done in 30 seconds

2017 Ford Focus hs rhk sucess bypass wait and programmed remote at same time.

2017 Ford Fusion prox. Sucess

2005 Ford Taurus! AKL

2000 Ford Focus. Owner had 1 key, computer said three. Erased and programmed 2 keys. Took longer to swap out the keys…

2008 ford ESCAPEE hi-bird

2013 Ford C-Max under y m m ten minute wait and done keyed ignition

2006 Ford 500 under y m m bypassed wait.

2010 Ford Fusion under y m m 10 minute wait.

2015 Ford f150 AKL .. h/s rhk 128 bit.

16 f150 add flip

2015 Ford Focus add 2 keys success

2007 Ford Escape under y m m bypassed wait.

2008 Ford Fusion under y m m bypassed wait .

2010 Ford F150 Super Crew. Add Key. H92 M/M/Y 10min bypass. Success

 

2005 Ford Escape … success… Akl, but used add key. In and out in under a minute. OBP remote.

2007 ford escape program 2 keys 10 min bypass fast

12 focus add key 10min wait

2001 Ford Mustang AKL success

 

2014 f350 add rhk. Sucess 10 min wait

2018 ford focus keyed ign. Success. Less than 4 mins

2010 Ford mustang add key success

‘16 Ford Flex smart key add success

‘00 Ford Expedition Success, no bypass

Ford > By System > Type 1 (HEC)

16’ Ford Escape. AKL. No wait

2012 Ford F150 Add Key Success 10 Minute Wait

2014 ford fiesta-dup plain key-10 minute wait

2000 Ford Ranger M/M/Y AKL 10 minutes done.

2014 ford escape Add key Advanced diagnostics 10 min AuteK 1.5 min

2010 Ford Fusion akl under y m m erased and programmed 2 keys 10 minute wait

2014 Ford Escape Add key, Did the bypass less than a minute

2017 Ford Explorer – add Keyless success. Less then 10 min.

2008 Ford Taurus program key

05 ford escape add key opt.1

2017 F150. delete all keys and program in new keys

Add Key 2014 Ford Focus Success

Add Key 2004 Ford F-150 success

2006 Ford F-150 AKL Success. Bypassed 10 minute wait.

Add Key 2000 Ford Focus success

2014 Ford Fusion under ymm less than a minute

 

‘05 Ford F150 > type 1 > All keys lost. Success. No wait

16 Ford explorer prox Had to wait 8 minutes then programmed in

 

2002 Ford Focus no wait

2003 Ford Focus AKL success. No 10 minute wait.

2010 Lincoln MKT pts chose ymm waited ten minutes and done

 

99 grand marques 10 min wait and done. 2 for 2

2013 Ford Edge add key success yay!

 

2011 Ford F150. Add Key. 10 min wait. Success

2013 Ford F150 Add a key success. 10 minute wait required.

2013 Ford Escape: AKL with 10 minute wait, success.

Ford Explorer 2001, ten minutes bypass. AKL, 2 keys cycle worked properly.

2002 ford f150 all keys lost. 10 min wait cycle both keys In.

 

02 Ford Explorer Trac 10 minute bypass Good2Go

2004 Ford Explorer 10 minute bypass good to go very quick

2014 Fusion (alarm on) AKL . Deleted & added 2 new keys. Not even 5 min.

2001 ford focus. bypassed 10 min

2013 escape akl add key h94pt

2017 F350 keyed erased in about 5 minutes and cycled in 2

15 fusion prox in about 5 min. Score!

 

08 ford explorer programmed

14 Fusion all keys lost with active alarm programmed in less than 2 minutes.

2008 Ford Expedition spare key

 

2008 Ford Fusion RHK (add Key) under YMM. If it took 30 seconds it was my fault for not going faster.

2012 F150. Add RHK. 10 minute wait and obp remote.

2015 ford escape. key programed crazy fast I would say about 2 min max . Loving this machine !!!!

AKL 2001 Ford explorer sport track programmed under 2001 Ford escape

Did a 2006 Ford Explorer Programmed 2 Keys in less than 2 minutes

Did a 2002 Ford Taurus programmed in 3 minutes

I did a 17 Ford Edge akl. Same prox as fusion. Alarm not active.

I did a 2017 F150. It worked fine. Didn’t go the full 10 min. More like 6 or 7.

2014 focus rhk , 2013 gr caravan, 2013 silverado remote all successful !!

2011 Ford f350 add key 10 minutes

2005 Ford Explorer 4 seconds

2014 ford focus USED smart key added. even though it say failure key was added. pressing unlock button 2 times on fob. The focus key part # 164-R8048. Ok

 

2012 ford fusion OEM key . fob and key programmed 10 minute wait OK

2014 ford focus keyed ignition 80bit key added NO problem 10 min wait.

2002 Ford taurus bypass programmed less than 1 m

 

To be upgrading...

Autek IKEY820 IKEY-820 New License For 2018 Ford and Toyota(G and H chip)Key Programming

Autek IKEY820 IKEY-820 New License for GM, Jeep Grand Cheokee and Dodge Durango Key Programming

 

 

Source:http://blog.obdexpress.co.uk/2019/10/29/autek-ikey820-for...