topblog Ivoire blogs

18/10/2019

How To Use Tacho Pro 2008 Change Mileage For Audi

Here is the  tutorial of how to do odometer correct for Audi with Tacho Pro 2008 July PLUS Universal Dash Programmer

Select the model:
1. Model A2 VDO
2. Model A3 / S3 VDO before model 2000
3. Model A3 / S3 UKNSI
4. Model A3 / S3 VDO model 2000 cluster plug
5. Model A3 / S3 VDO model 2000 clip

6.Model A3 / S3 Magneti Marelli model 2000
7.Model A4 / S4 VDO before model 2000
8. Model A4 / S4 UK NSI
9.Model A4 / S4 VDO model 2000 cluster plug
10.Model A4 / S4 VDO model 2000 clip

11. Model A4 / S4 Magneti Marelli model 2000
12.Model A4 Bosch model 2001 clip

13. Model A6 / S6, old model C4, before 1997
14. Model A6 / S6 VDO, new model before model 2000
15. Model A6 / S6 UK NSI
16. Model A6 / S6 VDO model 2000 cluster plug
17. Model A6 / S6 VDO model 2000 clip
18. Model A6 / S6 Magneti Marelli model 2000
19. Model A8 / S8 before 1/1999

20. Model A8 / S8 after 1/1999
21.Model TT before model 2000

22. Model TT model 2000

1. Model A2 VDO
Use this board and clip:

tacho-pro-2008-audi-1 tacho-pro-2008-audi-2

Remove the cluster and open it.
• Look for the 8 pin chip 93C86.
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 0.
• Put the clip on the chip 93C86 (red on pin 1).
• Select the menu Audi-A3-A3 2000- clip 2000.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

2. Model A3 / S3 VDO before model 2000
Diagnostic programming
Use the OBD II -plug:

tacho-pro-2008-audi-3

The diagnostic port is in the middle console of the car.
• Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port..
• Select the menu AUDI-A3-VDO-Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

3. Model A3 / S3 UKNSI Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it.
• Look for the 8 pin chip 93C56 (not the chip 93C46).
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 1.
• Put the clip on the chip 93C56 (red on pin 1).
• Select the menu Audi-A3-UK NSI-Clip.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

4. Model A3 / S3 VDO model 2000 cluster plug To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-6

Remove the cluster.
• Connect the blue and the green plug to the instrument.
• Select the menu Audi-A3-A3 2000-Diagnosis 2000.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.
Note:
If the displayed value is not correct, you can continue programming, most time it
works anyway.
You cannot destroy anything. If you cannot change the value this way, you have to
program by clip.

5. Model A3 / S3 VDO model 2000 clip To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this board and clip:

tacho-pro-2008-audi-7 tacho-pro-2008-audi-8

Remove the cluster and open it.
• Look for the 8 pin chip 93C86.
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 0.
• Put the clip on the chip 93C86 (red on pin 1).
• Select the menu Audi-A3-A3 2000- clip 2000.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

6. Model A3 / S3 Magneti Marelli model 2000To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-9

Remove the cluster and open it.
• Connect the blue and the green plug to the instrument.
• Also connect the black and the red cables like shown in the picture.
• IMPORTANT: You must not move the black and the red contact when
beginning to read until you are ready with programming. A good contact is
absolutely necessary.
• Select the menu Audi-A3-A3 2000-Magneti Marelli.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

tacho-pro-2008-audi-10

Note:
If the handhels shows you „out of range“ the contact was bad or the database may
be corrupted. For security reasons you cannot program the instrument at this
moment.
Normally it will be possible to program again after driving about 100 km.

7. Model A4 / S4 VDO before model 2000Diagnostic programming
Use the OBD II -plug:

tacho-pro-2008-audi-11

The diagnostic port is in the back of the car in the ashtray.
Note:
There are different instrument versions. To find the right one, you have to try which
one gives you the right value when reading. Reading will not corrupt the database.
But only program with the version that gives you the correct value!
• Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port..
• Select the menu Audi-A4-VDO old- Diagnosis
or Audi-A4-VDO old MFA-Diagnosis
or Audi-A4-VDO new-Diagnosis• The Tacho Universal shows you with one of these programs the old value.
• Enter the new value.
• Verify the new value with OK

8.Model A4 / S4 UK NSIUse this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Note:
There are different instrument versions. To find the right one, you have to try which
one gives you the right value when reading. Reading will not corrupt the database.
But only program with the version that gives you the correct value!
• Remove the cluster and open it.
• Look for the 8 pin chip 93C56 (not the chip 93C46).
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 1.
• Put the clip on the chip 93C56 (red on pin 1).
• Select the menu Audi-A4-UK NSI-UK NSI old
or Audi A4-UK NSI- UK NSI new
or Audi A4-UK NSI-UK 2 Eeproms
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

tacho-pro-2008-audi-12

9.Model A4 / S4 VDO model 2000 cluster plug
To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-13

Remove the cluster.
• Connect the blue and the green plug to the instrument.
• Select the menu Audi-A3-A3 2000-Diagnosis 2000.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

Note:
If the displayed value is not correct, you can continue programming, most time it
works anyway.
You cannot destroy anything. If you cannot change the value this way, you have to
program by clip.

10.Model A4 / S4 VDO model 2000 clip
To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it.
• Look for the 8 pin chip 93C86.
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 0.
• Put the clip on the chip 93C86 (red on pin 1).
• Select the menu Audi-A3-A3 2000- clip 2000.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

11.Model A4 / S4 Magneti Marelli model 2000
To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-13

Remove the cluster and open it.
• Connect the blue and the green plug to the instrument.
• Also connect the black and the red cables like shown in the picture.
• IMPORTANT: You must not move the black and the red contact when beginning
to read until you are ready with programming. A good contact is absolutely
necessary.
• Select the menu Audi-A3-A3 2000-Magneti Marelli.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

tacho-pro-2008-audi-14

Note:
If the handhels shows you „out of range“ the contact was bad or the database may
be corrupted. For security reasons you cannot program the instrument at this
moment.
Normally it will be possible to program again after driving about 100 km.

12.Model A4 Bosch model 2001 clip
tacho-pro-2008-audi-15

Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it.

tacho-pro-2008-audi-16

Pull off the needles for speed and rpm

tacho-pro-2008-audi-17

• Look for the 8 pin chip 24C08.

tacho-pro-2008-audi-18

Connect the clip to Port 3.
• Put the clip on the chip 24C08 (red on pin 1).
• Select the menu Audi-A4-A4 24C08
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

13.Model A6 / S6, old model C4, before 1997
Use those two plugs and connect them:

tacho-pro-2008-audi-11 tacho-pro-2008-audi-19

The diagnostic port is in the fuse box in the motorroom.
• Turn ignition on.
• Connect the Tacho Universal with both plugs to the diagnostic port.
• Select the menu AUDI – A6 – A6 old - Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.
Note:
If you cannot read the old value or or nothing changes when programming, let the
engine run. Maybe you have to try several times, also try different values, it will work.

14.Model A6 / S6 VDO, new model before model 2000

Diagnostic programming
Use the OBD II -plug:

tacho-pro-2008-audi-11

The diagnostic port near your left knee when you sit on the driver´s seat.
• Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port..
• Select the menu AUDI-A3-VDO-Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

15.Model A6 / S6 UK NSI
Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it.
• Look for the 8 pin chip 93C56 (not the chip 93C46).
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 1.
• Put the clip on the chip 93C56 (red on pin 1).
• Verbinden Sie die Clip mit Port 1.
• Select the menu Audi-A3-UK NSI-Clip.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

16.Model A6 / S6 VDO model 2000 cluster plug
To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-9

Remove the cluster.
• Connect the blue and the green plug to the instrument.
• Select the menu Audi-A3-A3 2000-Diagnosis 2000.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.
Note:
If the displayed value is not correct, you can continue programming, most time it
works anyway.
You cannot destroy anything. If you cannot change the value this way, you have to
program by clip.

17.Model A6 / S6 VDO model 2000 clip
To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it.
• Look for the 8 pin chip 93C86.
• Look for the silver chrystal and join its contacts.

• Connect the clip to Port 0.
• Put the clip on the chip 93C86 (red on pin 1).
• Select the menu Audi-A3-A3 2000- clip 2000.
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK

18.Model A6 / S6 Magneti Marelli model 2000To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000,
if it is mechanic it is an older model.
Use this plug:

tacho-pro-2008-audi-9

Remove the cluster and open it.
• Connect the blue and the green plug to the instrument.
• Also connect the black and the red cables like shown in the picture.
• IMPORTANT: You must not move the black and the red contact when beginning
to read until you are ready with programming. A good contact is absolutely
necessary.
• Select the menu Audi-A3-A3 2000-Magneti Marelli.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

tacho-pro-2008-audi-14

Note:
If the handhels shows you „out of range“ the contact was bad or the database may
be corrupted. For security reasons you cannot program the instrument at this
moment.
Normally it will be possible to program again after driving about 100 km.

19.Model A8 / S8 before 1/1999
Diagnostic programming
Use the OBD II -plug:

tacho-pro-2008-audi-11

The diagnostic port is under the ashtray.
• There is an old and a new version. The old version was built before 10/1996. If
the program shows you with the old version a wrong value, try the new version.
• Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port.
• Select the menu Audi-A8-A8 old-Diagnosis
or Audi-A8-A8 new Diagnosis
• The Tacho Universal shows you with one of these programs the old value.
• Enter the new value.
• Verify the new value with OK
Note:
If the new value is not displayed after programming, try this:
• Turn ignition off.
• Pull out the fuse for the odometer for a few seconds.
• Now the new value should be displayed

20.Model A8 / S8 after 1/1999
Use this board and clip:

tacho-pro-2008-audi-4 tacho-pro-2008-audi-5

Remove the cluster and open it
• Look for the 8 pin chip Chip 24C17.
• Connect the clip to Port 3.
• Put the clip on the chip 24C17 (red on pin 1)
• Select the menu Audi – A8 – A8 24C17 V1.
• The Tacho Universal shows you the old value. (if not, select the menu AUDI- A8-
A8 24C17 V2).
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

21.Model TT before model 2000
Diagnostic programming
Use the OBD II -plug:

tacho-pro-2008-audi-11

The diagnostic port near your left knee when you sit on the driver´s seat.
• Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port.
• Select the menu AUDI-Audi TT-TT Diagnosis.
• Enter the new value..
• Verify the new value with OK.
• For some models you have to enter the old value on demand.
Note:
If you cannot change the value, the cluster is model 2000

22.Model TT model 2000
Use this plug:

tacho-pro-2008-audi-9

Remove the cluster and open it.
• Connect the blue and the green plug to the instrument.
• Also connect the black and the red cables like shown in the picture.
• IMPORTANT: You must not move the black and the red contact when
beginning to read until you are ready with programming. A good contact is
absolutely necessary.
• Select the menu Audi-Audi TT-TT 2000.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

tacho-pro-2008-audi-14

Note:
If the handhels shows you „out of range“ the contact was bad or the database may
be corrupted. For security reasons you cannot program the instrument at this
moment.
Normally it will be possible to program again after driving about 100 km.

http://www.mileageprogrammer.com/

Les commentaires sont fermés.