topblog Ivoire blogs

19/07/2016

FGtech Galletto 4 vs CMD flasher vs Alientech Ktag Kess v2 vs MagPro

I was playing around with my MB Star C4 and Xentry 2016 developer mode

and I might have found a alternative to delete the ABC warning lights without a module.

Tested on 2003 Mercedes-Benz CL600 Base Coupe 215.376 5.5L V12

FOR THOSE WHO WANT TO CONVERT TO COIL-OVER and remove ABC suspension forever

So, here is what I found, someone can test it but you have to have DAS Xentry with developer mode.

I can’t test it as I already have the module installed and no time right now

If nobody can test it, I will do it one of these days

follow this:

Go to Control unit

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (1

 

->body

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (2

 

 

->CGW(cental gateway)

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (3

 

 

->development data

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (4

 

->control unit adaptations

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (5


->control unit adaptations (variant coding)

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (6

->globale variantencodierung

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (2


->nicht vorhanden

 

Mb-Star-C4-Xentry-Dev-mode-delete-ABC-dash-warning (8

 

(giving a 1000 thx to pmercury in the mbworld)

 

Invested on Chinese ECU programmers, FGtech Galletto 4, CMD flasher v1251, clone Alientech (Ktag and Kess v2), MagPro x17... I read a lot, with each opinion. Over all that I read is old (<2011).
So here's what I remember:

fgtech-galletto-4-master-bdm-tricore-obd-function-final.jpg
- FGTech Galletto 4: it is the best product, many times cheaper than the competition, at 40 euro you have a good Chinese clone for all cars, trucks, motorcycles, Marine, BDM MPCxx, BDM Boot Mode, checksum etc ... Good support

free-shipping-cmd-can-flasher-v1251.jpg
- CMD flasher v1251: The Must, one diagnostic interface, for reading and writing flash memory on the CAN line (not K-line) of computers with motor MED9.1, MED9.5, EDC16U3x/CP, EDC16CP31, EDC16CP36, EDC16C3 and EDC16C9 fuel injection. you need this tool only for new vag ecus, cause they are obd, even tprot

Magpro2-x17.jpg
- Magpro2-x17: This is very good for the latest ecu cars only and for Denso also you have good support .
All X17 owner will get new hardware soon, all in one tool, BDM, OBD, boot + +

ktag-ecu-k-tag-programming-tool-master-unlimited-token.jpg
- Alientech: Great tool, support is correct , but as soon as you want to touch anything other than car, it's very expensive too (full 20 000 euros) + XXXX euro subscription.

Chinese KTAG and Kess v2 runs the same software as Alientech
Ktag supports protocols: BDM MOTOROLA MPC5xx
Kess v2 supports Line, CAN, EDC17 and MED17 and Ford J1850... and Kess v2 truck version is available
they both work good, same as original and without tokens limitation, perfect with checksum, compared with FGTech

kess-v2-obd2-tuning-kit-vehicle-list.xls
kess-v2-truck-list.pdf
kess-v2-supported-truck-list-comparison.pdf 

05:21 Publié dans Blog, Shopping, Web | Lien permanent | Commentaires (0)

Les commentaires sont fermés.